Search results

  1. JacobHansen

    6.9idi head retorqueing.

    Hey guys, sorry it's been a while. Since retorqueing. My 6.9 still runs like a champ. Have lost track of miles but its used no coolant. Has Hot heat, no bubbles. No leaks.. It is leaking a good amount of motor oil from the heads but hey. Its an old truck. I haven't done a compression test...
  2. JacobHansen

    6.9idi head retorqueing.

    So strange.. it didn't leak any oil today.. well nothing notable.. and yes there's plenty in there. Im not convinced it sealed its self after a week of sitting.. After cleaning up the area in the picture I posted it hasn't had any oil build up or leaks at all. 40 mile ride this afternoon and not...
  3. JacobHansen

    6.9idi head retorqueing.

    It's from what I can tell a leak at the head gasket in the rear of the passenger side the small bolt to the oil galley is not the leak.. VC gaskets are new. I did retorque to 130lbs. The leak is pretty severe when the engine gets to operating temp. But it doesn't leak cold or on short drives...
  4. JacobHansen

    6.9idi head retorqueing.

    Ok guys thought I'd update and ask a few questions. Many many miles and worked pretty hard most days. Still no combustion leaks or loss of coolant. Truck still runs great after retorqueing the heads. But... im losing oil, passengers side back of the head. There is a small bolt that looks to be...
  5. JacobHansen

    6.9idi head retorqueing.

    Ok. I did the oil change...... wow almost 5 gallons came out.. maybe had over filled it huh? also found the dipstick tube was not in very far!. So i filled the filter then added 10 quarts. While I had it the shop I also removed the passenger VC. Inspected the gasket and surfaces. All checked...
  6. JacobHansen

    6.9idi head retorqueing.

    Can I completely eliminate it being the heads leaking due to the oil being above the head to block surfaces? I haven't had the chance yet to pull it apart yet . Going to try tonight. But while looking at it. There is definitely oil above the head gasket. But as stated its soaked under there too...
  7. JacobHansen

    6.9idi head retorqueing.

    Ok. That's what I was hoping to hear. I'll pull the cover and take a better look. Just got some oil so waiting on the filter. I'll pull the VC and post back what I find. Any ideas on how to un plug that drain hole if it is plugged? Jam a thin rod down it? Maybe air pressure would do it. Thanks.
  8. JacobHansen

    6.9idi head retorqueing.

    Heads are still holding strong compression and truck runs amazing was driving it daily until snow fall....although I'm losing oil bad on the passengers side head area. Has new VC gaskets and I made sure to snug up the hard to reach bolts good. My question now is.. how much oil should remain...
  9. JacobHansen

    C6 shutters in reverse.

    Ok so i started it up this morning. Went into gear fine back right up. I let it run for a little while. Maybe 4 minutes then checked the fluid. It was way over full. Im going to go ahead and change the fluid. Change the filter thing too. Could over full cause this? It only has the problem it...
  10. JacobHansen

    C6 shutters in reverse.

    Ok guys im looking for some help. My 4x4 c6 transmission. Shifts a little late on cold mornings. But smooth shifts. Normal shift is around 1800-2200rpm late is around 3000rpm (in my opinion) Its always been a little late going into reverse. Not more then 4-6 seconds. Witch seems like forever...
  11. JacobHansen

    6.9idi head retorqueing.

    Updated, its been quite some time and have been using this f350 pretty heavily and not extremely easy miles. Must be over 10k since retorqueing the heads. Have not experienced one problem yet with the cooling system. Absolutely no bubbing, steaming, only smokes a little on start up.. Id say...
  12. JacobHansen

    Aftermarket gauge ideas. 6.9 & 7.3

    Now thats what I was thinking. Wow nice work on those! I was thinking of using diamond plate if I go that route. I think my plan will be to make an insert simular to that. Maybe remove the clear case or some of it. and have the oil and temp covered by new ones, so the speedo and fuel can still...
  13. JacobHansen

    Aftermarket gauge ideas. 6.9 & 7.3

    Oh and can I put the water temp sensor in the bleed hole on the water pump? Or would that not be an accurate place for it.
  14. JacobHansen

    Aftermarket gauge ideas. 6.9 & 7.3

    Where do we put the oil pressure line on the motor? On the 6.9? Im sure the 7.3 is same. I didn't see any good spot. How is the one above the dash? A good spot for it? Iv been debating mounting out front of the o.e.m. gauges.
  15. JacobHansen

    Aftermarket gauge ideas. 6.9 & 7.3

    Who has pictures of there gauge pods, triple or dual. I'm looking to install a set for oil and water. But want something tasteful not just screwed on dashboard. Before I go cutting and re arranging. How's it set up and where did you put it?
  16. JacobHansen

    6.9idi head retorqueing.

    Well what's most satisfying is that since it did work. Im pretty certain that the gasket surfaces are going to be good when it does need replacement. And the heads are not cracked. Again maybe this will change but it makes the head gasket job a little less nerve racking. I was worried the heads...
  17. JacobHansen

    The Official "Show Us Your Ride" pictures of member's trucks thread.

    My 87. When I bought it and now. Leveled and 35s. Extra lights. Lots of tcl love this thing. 6.9 non turbo.
  18. JacobHansen

    6.9idi head retorqueing.

    For the guys who don't know. My truck 6.9 idi had extremely high pressure in the coolant system causing loss of coolant through the degas tank. And bubbing in the tank. Otherwise it ran good. Was very loud at shut down from the bubbing coolant Ok guys, so I went ahead and retorqued the heads...
  19. JacobHansen

    6.9idi head retorqueing.

    Thanks for the help guys. It's a blown gasket now. I drove it to a friends garage to do the work this weekend. And it started smoking from the tail pipe. And really blowing pressure into the coolant. I just ordered the head gaskets. Maybe it would have save a little time if i had caught it...
  20. JacobHansen

    6.9idi head retorqueing.

    Thanks. Major help. I will get after it this weekend and let you guys know how it works out. Good or bad. I know its a long shot but hey, It should be done anyway right.
  21. JacobHansen

    6.9idi head retorqueing.

    Any pointers on the state of the engine beforehand? Should i get it warm? Do the timing marks need to be aligned? The rockers go back to ther original places? Im only so worried because I love this truck but can't get the heads done right now. Don't want it sitting. Don't want to make it worse...
  22. JacobHansen

    6.9idi head retorqueing.

    Great advice. I will retorque this weekend. I have a 7lb cap i can throw on too. Thanks
  23. JacobHansen

    6.9idi head retorqueing.

    I'm going to look for the oem torque sequence. Unless its on here somewhere? Has anyone had luck stopping the combustion leak by retorqueing? Im not sure of true miles and its been hot. Once overheated but was only spiked for a min while driving. Lack of coolant. Cooled down once the fluid...
  24. JacobHansen

    6.9idi head retorqueing.

    Thanks. Much appreciated. Valve cover are seeping ya. Ill do that. Maybe it will help thanks again.
  25. JacobHansen

    6.9idi head retorqueing.

    Hi im new to fords,diesel, forms, and combustion gasses getting into my coolant. The rig is 1987 f350 6.9. C6 auto. 4x4 crewcab. No obvious signs of head gaskets leaking and runs very smooth. But tested positive for combustion gasses in coolant, it was boiling some off and gurgling so thats why...

Latest posts

Forum statistics

Threads
91,280
Posts
1,129,761
Members
24,098
Latest member
William88

Staff online

Members online

Total: 660 (members: 12, guests: 648)

Share this page

Top