Thats what Im thinking but I seen in another post about identifying crossmembers and he also had a 4wd with the same as me. Looks like ill be searching again for another crossmember or combining the old e4od one with this one so it drops down on the shaft side.
and thanks! Its not restored but...
The t-case yoke sits in line with the crossmember so using the f250 shaft can't be done without cutting the crossmember. its like i need the double cardigan to extend the shaft forward to clear the crossmember and then down to meet the d60. Ill have to post up some pictures. Maybe I have the...
Ok i guess the search for a yoke or f350 t-case is on. I had the f250 shaft in when i D60 swapped and it worked fine. But with the zf5 its obviously too long and hits the crossmember
Yeah I figured I need the f350 double joint shaft no matter what. But I'm more worried that it won't bolt onto my f250 t-case. I did more research and I think that will be the case. Either get a f350 t-case or find a yoke. I do know they make adapting u joints so I may go that route as well.
Hi all I have been running my truck all summer now (1994 F250 7.3 4wd) and finally have some time to finish my zf5/d60 swap. All I need is the front driveshaft. Supposedly I have the correct crossmember (even though it looks like the driveshaft would hit) but I need help on what shaft to...
I think I have it figured put guys, I plug the truck in for an hour and boom. fires up immediately after the WTS light goes out. I have a short to ground in the glow plug harness. unplugged harness from controller and all glow plugs, 7ohms at connector to ground. Ill be ripping it out and...
So tonight I installed a pressure gauge between lift pump and injector pump. Reads 8psi idle and down to 4-5psi 2k rpm. Thats facet pump- no regulator. Then I installed clear hose on the return side. no bubbles seen anywhere. I even checked my timing (which is dead on) and still no bubbles. Let...
I removed my pressure regulator and installed a clear hose from the lift pump to the injector pump keeping the check valve I added in place. It actually started up a lot faster this time and once running no air bubbles are seen. Do you guys think a facet (unregulated) can cause my timing to...
I wouldn’t be worried about the noise. Definitely will be considering that pump. The only thing that I wonder about is I keep reading a electric pump will band aid a return line air intrusion problem. If that’s the case then none of my return system should matter right? The truck should still...
I had the feed line before the injector pump and the return line clamped overnight. Tonight I Just removed them and it read 4psi on the lift pump. I let the wts light shut off and cranked it for 5 seconds. Nothing. Fully cycled the key and throttled halfway and it fired right up. So if this is...
What pump would you recommend? If I clamp off the faucet on the inlet and outlet it holds pressure over night until i unclamp it so I figure id rule that out
I might have to try one of his kits. And I do have a check valve between the electric lift pump and injector pump. I just think it’s weird if I have the return clamped off and the lift pump supply clamped off, the regulator pressure drops to zero in a hour. But I don’t think this is anything...
Hi everyone so here the back story, 94 idiT fully rebuild engine 3 years ago.New everything- short block ,heads, R&D inj pump, injectors. Facet lift pump with 7psi regulator in engine bay. I deleted fuel filter setup and relocated to frame with. Engine always started up and ran great.this last...
Here is my 1994 F250 IDIT. Im second owner, my father in law is the original. 125k miles. I think about everything mechanical has been replaced throughout the years lol.only stripe and lower blue was painted. Above stripe is still original.New factory trans, Diesel Dealer short block, redone...
Do you happen to have a picture of your crossmember? Just so I know what I’m looking for.mines basically 1” higher than a stock f350 so the ZF5 F250 crossmember should work for me
I have no problem modifying haha might even make my own if it comes down to it. I just didn’t want to have 5 crossmembers bought just to see what one I need. Realistically shouldn’t a F250 4x4 ZF5 crossmember be what I’m looking for because I have a f250 4x4 truck?
I have to look when I get home Wednesday. Currently out of town for work.its hard finding the f350 4x4 one. I was told a F150 5spd would work as well but idont don’t forget sure. I just finished putting a dana60 Plus 1” block in my truck so now it sits 3” higher if that matters
Hi guys I’m just about ready to start swapping in my ZF5 transmission but still don’t have a crossmember. My truck is a 1994 7.3idiT 4x4 with e4od in it. Now I’ve been searching just about every thread to do with a ZF5 and found nothing. So here’s my question: Since I have a F250 4x4 would I...
well hopefully it didn't do any damage. the plug got sucked into the cooler and bent the fins a little but that's it. Put the new o rings on today and will be lock titing the plug back in. If it fails again and the new motor blows then ill have a cummins swap to look forward to:Thumbs Up
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.