Search results

  1. shawn deere

    Flickering Battery Light

    Ah crap
  2. shawn deere

    1993 7.3IDI Turbo white smoke after IP, injector replacement

    The dead cylinder sound, yesssssss. I heard that on mine. It sounds like a hole is missing right? I crack all 8 injector lines with it running not a single one seemed at fault. Every injector seems to be missing a little bit randomly. Ill check back in when i get the new lift pump and air...
  3. shawn deere

    1993 7.3IDI Turbo white smoke after IP, injector replacement

    Might check tank selector valve, i think ive heard of them leaking - letting air in the fuel system before.
  4. shawn deere

    1993 7.3IDI Turbo white smoke after IP, injector replacement

    Hey there. My pickup is doing the about same thing. My electric lift pump is leaking im pretty damn sure its sucking air and mixing with the fuel. New lift pump is on the way for me. Its the second holly red that crapped out btw, going with a dura lift this time
  5. shawn deere

    RADIATOR QUALITY

    I think i got mine for $400 give er take. Looks sweet too
  6. shawn deere

    RADIATOR QUALITY

    Ive got a mishimoto aluminum radiator. So far its super
  7. shawn deere

    Slip joint up pipe?

    Id leave it man. You can beat it apart then itll start leaking. Itll be black if it was thinking of leaking. I actually welded mine cuz it was loose...
  8. shawn deere

    Gelled lines

    Or gas if your cheap. Lol
  9. shawn deere

    Uugghh now what

    The gear vendor, ive never been around one, but they dont have a straight through gear ratio, do they? And they’re after the T case changing only the rear axle ration correct? Sounds like you might need to jack up the front axle and spin some tires to get thing to unlock
  10. shawn deere

    Need Ignition Switch???

    I have an entire steering column laying around :cool:sly lol. Did they smoke when the gpc was running? I hate the gpc... fact i have a spare riding shotgun with me
  11. shawn deere

    does upgrade to 12 inch clutch require different flywheel?

    Ive got the stage 3 south bend clutch. 3.55 gears i think the tires are 33” or 34” now. Haul heavy at times (25k#). Havnt slipped it once. Even got stuck in some sand empty, revved up dumped clutch, killed engine. Twice. It wasnt smart, was a matter of pride after the first go. Ended up...
  12. shawn deere

    W80: keeping it mixed

    Still dont have mine going -_- Someday. I cant wait to get burned out of waste fuel. Lol
  13. shawn deere

    Fuel filler neck woes need ideas

    I have seen this in action! Dude had doors to cover fill caps. And had a load of square bales on. Pry 30 or so. And had to fuel up. I laughed Could block up the entire flatbed for a more favorable angle. If you want a super tall flatbed that is
  14. shawn deere

    Axle questions

    I believe theres a complete write up on the swap somewhere
  15. shawn deere

    W80: keeping it mixed

    K gents. I think its a drainage problem out the bottom of the fuge Was aiming for a 'fuge into the next barrel and let it settle a while' tactic. Have two plates ill try the bigger one again. Ill shorten it and torch the hole a bit bigger. Dont mind the water. We got half our annual...
  16. shawn deere

    W80: keeping it mixed

  17. shawn deere

    W80: keeping it mixed

    Pressure is good to go, i can keep it at 90-100 no problem I think its not draining fast enough and getting backed up into the rotor. Ill get some pics of my setup sometime and post em up. I built two plates one with a 1/4" pipe to drain into the little hole of a 55gallon drum One has a 1.25"...
  18. shawn deere

    W80: keeping it mixed

    The pressure is still there, i can just hear the 'fuge slow down and stop
  19. shawn deere

    W80: keeping it mixed

    Man, ive got one of them little blue oil filter canister lookin fuges, it just wont spin right.... Itll wind up, then slow down to a stop. Dropped some coin on the setup, gear drive pump, pressure gauge, brass valve and all so i can adjust the pressure to 90psi
  20. shawn deere

    W80: keeping it mixed

    Has anyone started a drum on fire with the gas mixed in? I hate to be the first. Lol 73% 15-40wmo 27% gas. Mixing with an air nozzle
  21. shawn deere

    1991 f-super duty 7.3 idi n/a

    X2
  22. shawn deere

    Trying to replace thermostat, cant find replacement rubber seal

    I made mine out of gasket material
  23. shawn deere

    Project Big Red

    Mine started with hex studs, removed em and put in hex head free studs on passenger side only
  24. shawn deere

    Machine shop aggrivations

    Maybe look into the moose head shims? If you have the cheddar. Might be on par with milling the pistons.
  25. shawn deere

    Just getting started

    :rock:

Latest posts

Forum statistics

Threads
91,276
Posts
1,129,687
Members
24,098
Latest member
William88

Members online

Total: 449 (members: 7, guests: 442)

Share this page

Top