Search results

  1. Robm45497

    Turbo oil feed

    Yes, i would find a long chisel or one that i could sharpen to get a good bite on at a angle. I have had harder places like at the rear of my sprinter van that i could not see but only feel to get a nut welded on (not enough room to chisel or air hammer at a angle to get turning). There can be...
  2. Robm45497

    Turbo oil feed

    weld a nut or use a hammer and chisel.
  3. Robm45497

    what goes into pulling an idi?

    make sure to pull oil filter off to help clear the cross member especially if you have the 1995 filter
  4. Robm45497

    what goes into pulling an idi?

    I would drop tranny transfer case out the bottom still married
  5. Robm45497

    what goes into pulling an idi?

    when my truck was stock height i pulled hood bolts and rotated back and with a harbor freight picker could get over the core support with just the motor. when lifted i pulled the core support. I still think it is easier to seperate in the truck and build a plate to bolt to floor jack for tranny...
  6. Robm45497

    The Official "Show Us Your Ride" pictures of member's trucks thread.

    Had the interior out when I did the motor and rsk this last summer.sound deadened the cab and new carpet but trying to figure if I should change out seats now
  7. Robm45497

    6.9IDI Nightmare

    S and j here in spokane wa. can do a engine.
  8. Robm45497

    Onan/Cummins Diesel generator: overheats after 20 minutes of running

    Maybe fuel pump going out? we had one that would start and run then stop. We were on the road and couldnt wait for parts so we got a cheap electric pump and rerouted the fuel line till we got it home to get the proper pump. Ours was gas though.
  9. Robm45497

    Holes on the sides of injectors

    sometimes they are hard to seat The_Josh_Bear stated.
  10. Robm45497

    Oil leak

    Did you punch big holes in the valley pan for the turbo oil line return. If not it could be that location. I didn’t do it and leaked very badly. The stock holes in the valley pan would not flow enough to overcome the amount coming from the turbo
  11. Robm45497

    CORRECT FUEL LINE FROM FILTER TO INJECTION PUMP FOR 1994 UHAUL VAN.

    Thanks i ordered the rubber one from you
  12. Robm45497

    CORRECT FUEL LINE FROM FILTER TO INJECTION PUMP FOR 1994 UHAUL VAN.

    Thank you , do you guys worry about the hose degrading and particles getting into the ip. Even if you use a filter near the end you will still have a hose at the end? Just wondering if anyone has had a problem with this. Thanks again
  13. Robm45497

    CORRECT FUEL LINE FROM FILTER TO INJECTION PUMP FOR 1994 UHAUL VAN.

    Looking for fuel supply line from filter to injection pump. 1994 e350 idi na old uhaul box van. Need line or correct part number. Thank you
  14. Robm45497

    Reman engine for sale anywhere?

    S&J IN Spokane ,wa.
  15. Robm45497

    Finding an engine stand for an IDI, not easy

    the 2000lbs harbor freight works ok. It will rotate pretty easy till you get the heads on. Then it is a little harder but will still rotate.
  16. Robm45497

    Installed turbo kit

    I didn't do it the first time and it presurized and leaked very bad. Had to then do it in the truck and it was a pain in the ass.
  17. Robm45497

    Injector cores

    i would take them so i can have a extra set to get done without having the truck down
  18. Robm45497

    surging, hesitation

    4th gear at 25mph, your lugging it to much.
  19. Robm45497

    Anyone using new Banks, Hypermax, R&D, or home made turbo kits?

    i did a R&D stage 3 turbo kit. Im very happy with it. Ive done conversions on small block 4 wheel drives to big blocks. Done a lot of motorcycle stuff in the past but have a small buisiness i run,my son used to do flattrack and take alot of my time and i just didnt have time to due all the...
  20. Robm45497

    Power window disfunction

    over the years the wire becomes brittle and will break or fray from opening and closing the door. If you pull back the rubber insulator between the doow and fender i bet you will find problems with the wiring making and not making contact.
  21. Robm45497

    Radiator leak. 90 miles from home with camper a

    i've used pepper before in a pinch
  22. Robm45497

    '93 Crew cab exterior clear plastic grab handles

    Drill them and put leds inside
  23. Robm45497

    Tapping sound on my 7.3 idi that gets louder as it gets hot.

    or cracked manifold
  24. Robm45497

    EC-1 coolant in IDI?

    i use Evans in my dirt bikes and my kids flattrackers. Did not check into it for a idi. I have recommended it to others for their hot rods.
  25. Robm45497

    Windshield wiper governor

    I had problems with my wipers,they would work good on the higher delay settings but on the lower they would work and then stop or stop mid wipe and not continue. I took the steering wheel control switch apart and cleaned and die electric greased(no change) i then pulled the wiper relay by the...

Latest posts

Forum statistics

Threads
91,280
Posts
1,129,728
Members
24,098
Latest member
William88

Members online

Total: 396 (members: 4, guests: 392)

Share this page

Top