Hello, I am in need of the rubber clutch fork cover for my ZF5 and the boot that attaches to the bottom of the shifter in the cab---let me know. ----- Rob
If you buy from this outfit in Florida,it will be a risky transaction. I bought a set of heads from them recently. I received the heads and took them to my machine shop for the install.Later in the day I received a call the shop saying the heads were junk. looks like they had installed used...
Hey guys, search didn't work so well. My question is, where can I get a flywheel that bolts up to a 6.9 engine so I can use my ZF 5 speed? hopefully this is possible---Rob
Hello everyone, I am wanting to make sure my heads off a 7.3 will fit a 6.9 without any issues. I asked this question and Gary mentioned a few members have already tried it. I had someone tell me that the 6.9 cups should be put in the 7.3 heads, Anyone know if this is necessary? I am going...
I am in need of a steering column for my 88 with a manual transmission and it is a tilt column. one of the ears that hold the tilt mechanism has broken off on mine. I don't need steering wheel. ---Rob
working on my truck over the weekend,Installed a glowplug controller. Went to start the truck and no power to the controller happened. Then turned the key to off and truck remained running! rats!! so I am assuming this is a wiring problem in the wires going down the column. \Ordered a new...
Does anyone have that adapter that bolts to the front of the injection pump that runs to the cdr valve on a banks turbo setup? I sure am in need of one. ---Rob
recently pulled my power brake booster and can see the firewall is starting to crack around the clutch.Could some post a link to the "guy" who has the large bracket for sale?
Hello guys, I have put a clear line on the filter to # 1 injector and have a huge air bubble.Hardly any fuel is showing in the clear line.I pulled that fitting off the filter head and a spring came out,not much else.is that normal? any idea where the air might be? if it wasn't for my electric...
for sale is Snap-on timing device,luminosity and inductive,two separate units,also a sears craftsman timing lite with adjustable degrees. all for one money.how about $300.00 shipped?---Rob
went to roll my driver side window up,it went up about 2 inches and then disappeared! so I thought crap new motor time. But no. When I pulled the door panel off the crank arm had slid out of the window track!! well, after putting the arm back on the track its not going to work .the arm now...
Hello Everyone. Like the title says My high beams won't light. When I hit the foot switch everything goes dark. Replaced the switch and still the same problem. I have low beams. Any ideas of where to check next ?---Rob
Does any pay attention to the notice that came with the cowl induction unit. mine said to remove the flexible tube from the plastic piece in the event of heavy rains.I have yet to remember to do that.:D However this morning, When I went outside,the truck was covered in a sheet of ice.Scraping...
Hello everyone, while removing all turbocharger parts from my truck this weekend:D I noticed a large rivet that's holds the crossmember, front frame piece and long frame was poking out of its hole. I used a bottle jack and pushed it tight up into its hole. However this cant be good. So want I...
I have a us gear exhaust brake unit installed on my truck ( it came with the truck) the red push button has quit working. I called us gear and they said too bad,so sad. the buttons are no longer in stock. I know the battery can be replaced but the push button no longer works also. Anyone...
Hello ya'll,I recently installed a Hypermax turbo charger. When I reinstalled my electric oil pressure gauge I put a T where the oil is fed to the turbo on top. My oil before install was 40 psi on the freeway, after the install it went to 21 lbs. yesterday pulling a flat bed trailer modestely...
I also have problems with air intrusion sinse replacing my injectors. I installed new o-rings hoses and clamps. some of the caps did not "snap" on when I installed them.I recently read a thread where someone mentioned installing an old O ring on top of the cap and then tighten on down the...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.