Search results

  1. Runningaford

    is this a good deal?

    Hi All, I'm going to look at this in the AM ---->>> https://spokane.craigslist.org/cto/d/spokane-bus-93-ford-350-diesel-73-engine/6799238953.html I don't think there's too much history, short of it being abused, or rusted out, it seems like a good deal; any thoughts? Appreciated in advance.
  2. Runningaford

    51' White COE 4x4 12v Cummins

    I wish I could afford! http://spokane.craigslist.org/cto/d/1951-white-cabover-12v/6386980777.html
  3. Runningaford

    Jeff's bronco graveyard alternator

    Hi all, I'm not sure where I read it, but some how I got the great idea to use one of Jeff's Broncograveyard alternators on my truck. It came with no instructions, and it isn't just plug, and play. I think it's a 3g alternator, but actually don't have a clue. In all honesty, call me a...
  4. Runningaford

    clutch acting up, any advice?

    I've searched the topic, and am trying to pinpoint the issue. About a year ago, I rebuilt the clutch cross pin shaft, and installed the heim joint to the end of the master cylinder arm. Today while in traffic, the clutch pedal spring stuck the pedal to the floor; no clutch, so I took a page...
  5. Runningaford

    86' F250 extended cab 4x4 6.9L 158k w/camper trailer $8,000

    http://wenatchee.craigslist.org/rvs/5832117542.html
  6. Runningaford

    turbo update

    In my other thread, looking for a turbo actuator valve cookoo ,based off of the 'professional' advice of a 'professional', and fairly strong looking diesel shop business:backoff In reading the posts, towcat got me to really thinking about wth was going on. I went to the University of Youtube...
  7. Runningaford

    093 vacuum actuator

    Greetings, I just recently installed my rebuilt turbo. It was only getting around 4psi of boost with decent acceleration, and 0 most of the time. I checked for leaks everywhere, and found none. I took it into a diesel shop to have them try to figure it out. They're telling me the vacuum...
  8. Runningaford

    built 7.3, banks sidwinder, turn key motor

    I don't think it's built, just resealed....... the turbo set up looks homemade, and figured you guys would find it interesting..... Would this even work very well?:confused::dunno http://seattle.craigslist.org/see/pts/5462038083.html $2,300 "I have here a 94 Ford 7.3 idi with a Banks...
  9. Runningaford

    Trailer brake question

    I know a lot of guys here run a trailers, and would have a trailer brake. I bought all the stuff for an aftermarket installation, but since then, through reading, found that many trucks came with a factory tow option.... I crawled under the rear end just now, and saw two connectors open, one...
  10. Runningaford

    Turbo install

    Okay, I've been working on my turbo install, very slowly; in between other things. In all honesty, I've never done something as 'intense' as this is, and am just gonna layout what I've done so far, and more toward the bottom are my more concise questions. replaced the stock valve covers...
  11. Runningaford

    air intrusion?

    I've been slowly working on getting my truck ready to add the turbo I bought. So far I changed out the valve covers to the turbo covers, and put in the turbo wiring harness today. I wanted to crank the truck up, and make sure all to this point was 'good to go', and let it run before moving on...
  12. Runningaford

    1989 Ford F250 4x4 7.3L IDI (non turbo). - $1200

    Wish I were in Tucson to take a look at this. http://tucson.craigslist.org/cto/5414345489.html "Mechanic's special, not running-possible air in the system according to mechanic. Will need to be towed away. Has new fuel and oil filter. New glowplugs also installed. All new engine belts also...
  13. Runningaford

    7.3 idi Turbo, pasco washington

    http://kpr.craigslist.org/pts/5408299961.html Complete kit to turbo a 7.3 idi. New cross over pipe, 3"down pipe, up pipe, and y connector. Rebuilt turbo new bearings and seals. Has pedistal, intake adaptor, and oil line. This is a COMPLETE kit. I bought this kit for a rat rod project and...

Latest posts

Forum statistics

Threads
91,266
Posts
1,129,519
Members
24,094
Latest member
madmustang1965

Members online

Total: 506 (members: 2, guests: 504)

Share this page

Top