Search results

  1. laserjock

    Oilburners 2019 Gatlinburg Rally

    That’s a bunch of crap. [emoji849] We are 2 adults and a 7 yo on 208 all week.
  2. laserjock

    Project Time Bandit

    The dodge guys swear by XRF.
  3. laserjock

    Do I need to "wait to start"?

    This was my original plan but I somehow got things twisted up in my wire harness so I punted. It’s nice to have some control over it. I can short cycle it just by flipping the switch on and back off. It kills it as soon as the switch is off.
  4. laserjock

    Do I need to "wait to start"?

    I put a kill switch in to my controller. After it starts, I turn it off and I’m good for the day usually. If it sets all day and gets stone cold, I flip the switch back on and the controller takes over. Sorta the best of both worlds as far as I’m concerned.
  5. laserjock

    Project Time Bandit

    What he didn’t mention is how long it’s taken him to get to that point. [emoji16][emoji16][emoji16] LOL LOL He’s winning but it’s putting up quite the fight. Wish I was closer. I could at a minimum drink beer and laugh at you in person. What are friends for right?
  6. laserjock

    Project Big Red

    You and all your logic. That has no place here!! LOL LOL LOL
  7. laserjock

    Project Big Red

    I looked for one but everything I found was short. Is the hump hose just to let it flex more? I don’t really see the purpose otherwise.
  8. laserjock

    Early Banks, water cooled turbo

    This^^^^ If it has water fittings it needs water. All of Garrett’s literature I’ve read reinforces this. If it’s done right, a ball bearing turbo should have MUCH less oil going through it than a journal bearing. The oil is the coolant on the journal bearings. The ball bearing turbos need the...
  9. laserjock

    Project Big Red

    Didn’t take any pictures but it pulled the charge pipe off the turbo on the way to work the other day. Ordered a 6” coupler and trimmed about 1.25” off it. Lots of pipe in the boot now. Should be good to go. I’ll be putting up my pre-rally list soon.
  10. laserjock

    Early Banks, water cooled turbo

    If it’s a garret center section it’s probably a metric straight thread for a face seal or banjo bolt.
  11. laserjock

    Project Big Red

    That was a little one. River was full of those browns. Caught some really nice rainbows. 16” of rainbow trout jumping out of the water on 4lb test and a 9’ toothpick for a rod is a good time.
  12. laserjock

    So what did you do with your truck today?

    This is why I use the washer fluid. You are absolutely right. After a while, the wipers take it off. Hit the squirters and if it’s not completely toasted, it comes back pretty easy. You have to keep up with it though. Give a shot ones in a while when it’s not raining or raining lightly. The...
  13. laserjock

    Project Truck - 89' F250

    4.10 my truck had a yellow gear in it. I switched to maroon/wine with the 3.55’s and the speedo is spot on.
  14. laserjock

    Project Big Red

    Of course I don’t have another one. The black grill and silver grill use a slightly different one than the chrome. It’s shaped different on the back. On the trip home in the rain it really sucked. Totally blind the entire way. Got to fix that somehow. Going to try rainex first...
  15. laserjock

    Project Big Red

    Trip report time. So really it was a pretty uneventful trip as far as the truck was concerned. Traveled out I-68 truck and trailer. The headwinds were absolutely brutal. Like 30-50 mph brutal. Truck got pretty warm on Big Savage but cooled right off at the summit. I’m not sure the fan ever...
  16. laserjock

    Engine rattle and white smoke

    The real question is what does the smoke smell like (not from the roast although I’m sure it was more pleasant). If it’s diesel look at the injectors. A bad injector will make a lot of noise and smoke. If it smells like coolant.... well.... that’s a less pleasant situation most likely.
  17. laserjock

    fuel pump

    He’s running a FASS and right now he’s not a fan. LOL
  18. laserjock

    fuel pump

    There’s a specific bbc plate that fits without modification. Watch and make sure it sets flat. The block casting can get I. The way and it will never seal if you get the wrong one.
  19. laserjock

    Carrier/facet pump observations

    I have a hard time getting mine to drop. Just free reving it really doesn’t seem to do much. I want until she was loaded and working hard that it made a noticeable difference. I’m still very curious to see how this shakes out.
  20. laserjock

    Carrier/facet pump observations

    I think what that data is telling you is that the limitation is your plumbing not the pump. Which tank were you on? I can see a difference from front to rear tank. I suspect the difference is several more feet of line.
  21. laserjock

    Carrier/facet pump observations

    There’s a thread here somewhere that Mel discussed the effect of fuel pressure on the pump. I don’t have time to look for it but I seem to remember for every 1 psi over 7 (I think) you loose 1/4 degree of advance. If memory serves (and that’s shakey) it really only affects the bottom end...
  22. laserjock

    Carrier/facet pump observations

    I thought about running one on a pressure switch but I digress. I’m in the same boat. On the front tank, I’m not starving for fuel wide open at pushing 3k. So for now, I’ll make sure I’m on the front tank for hard workouts and any other time it doesn’t matter. If this pump dies, I may jump up to...
  23. laserjock

    So what did you do with your truck today?

    You know, I wondered the same thing. I use the Rainex washer fluid and love it. Might be worth a shot. The windshield stuff works great for actual rain at speed. Fabulous. For misty rain and road spray it doesn’t do much good. That’s been my experience.
  24. laserjock

    Carrier/facet pump observations

    I did exactly this. My inlet line is a 3/8” to 1/8 npt stainless swagelok fitting that has been bored through to something over 1/4” ID (closer to 5/16” but I don’t remember exactly). It had plenty of meat for structure. It’s not like we are dealing with high pressure here. IIRC the outlet...
  25. laserjock

    Carrier/facet pump observations

    Question. Does it still use 1/8 npt inlet and outlet fittings or did it jump up to 1/4? I would hope with the bigger hex bits it would have bigger fittings but maybe not.

Latest posts

Forum statistics

Threads
92,996
Posts
1,155,942
Members
26,575
Latest member
Gerhard

Members online

Total: 1,582 (members: 2, guests: 1,580)

Share this page

Top