Search results

  1. ADV

    Aluminum injector caps

    From what I have found the plastic caps are not very consistent with the inner diameter. Some are egg shaped and some are bigger and some smaller. The original gray caps are the best from what I was measuring.
  2. ADV

    Aluminum injector caps

    A turbo setup you need 2 90s, 2 dead end, 2 T's and 2 straight through?
  3. ADV

    Aluminum injector caps

    Thanks I was not sure if all 3 fittings were on the same side or not. Well I guess it don't matter what would you guys prefer.
  4. ADV

    Aluminum injector caps

    I have not made any T caps yet. This might be a dumb request but can some one post a picture of the plastic t cap? Every truck i am working with are NA trucks.
  5. ADV

    Aluminum injector caps

    well slowly slowly moving forward on this little project. I got dumped on with so many side jobs the last few months I did not hardly have time to make what I wanted to make. I just finished up two more sets of aluminum caps one set for my dad and one set for a friend that's also a member on...
  6. ADV

    water temp gauge question

    I finished up the install and hooked up my guage today. I drove the truck about 10 miles at 55mph and only seen a reading of 185 for temp. My factory guage don't move much either. It was about 35 degrees out. I have a new thermostat and water pump to put in we will see what it is after...
  7. ADV

    Champion Radiators for the IDI

    How will an aluminum radiator hold up to road salt?
  8. ADV

    1993 Crew Cab flatbed project.

    Cool truck!
  9. ADV

    water temp gauge question

    gauge ordered. where is the best place to put the sending unit? Thanks everyone
  10. ADV

    water temp gauge question

    i like your idea with the elbow. is that just a plastic elbow?
  11. ADV

    water temp gauge question

    I think I am going with the 140-280 mechanical guage. Now I just need to figure out where to put it
  12. ADV

    water temp gauge question

    Mechanical sending unit better than electric? The 140-280 guage is mechanical. So a normal idi water temp is 220?
  13. ADV

    water temp gauge question

    I am sure this has been covered on here but I cant find what I was looking for. I am planning on adding a water temp guage to my truck. Along with new water pump, thermostat, coolant filter and swapping the radiator. I was going to go with a z series auto meter to match my egt gauge but...
  14. ADV

    Clutch Switch OverRide??

    I bypassed mine and put a toggle switch under the dash.
  15. ADV

    ZF5 with parkin brake

    I think he went to ford and got a new one. His was messef up beyond repair. So realistically whats it worth?
  16. ADV

    ZF5 with parkin brake

    My dad is trying to recover some of the money he payed gor the parking brake. So this probably is a crazy number but its where he wanted to start.
  17. ADV

    ZF5 with parkin brake

    Zf5 s 5-42 transmission out of a 1992 fsuperduty. Shifted good through all gears but would not always like to go into reverse. Truck had about 165000 miles on it when it got pulled apart. It will also be missing one inspection cover I am keeping the pto. Parking brake assembly was bought...
  18. ADV

    Sorry if I let everyone down

    So first off I would just like to say sorry to the few people I told I was going to send parts to and never did you will get them i just need more time to finish what i started. Its been a crazy year so far with work and everything else. I have had so many side jobs given to me this year its...
  19. ADV

    Aluminum injector caps

    I am still here. Aluminum caps still on my truck and still working good. Its about a 3 hour process to make a full set of caps and i just have not had the extra time at work to make any recently. Sorry this is taking so long.
  20. ADV

    steering column bearings

    Working on my floppy steering wheel in my 93 do I need to pull steering column out to replace bearings?
  21. ADV

    -5. stupid cold

    Truck ran for 15 min to warm up then I hit the button to see if it worked and it did. New solenoid on the work bench just need time to put it in.
  22. ADV

    dirty northern truck

    Typical Wisconsin truck mid winter. There is so much salt on the roads right not there is a salt dust cloud that gets kicked up when you drive. I looked at the clean southern truck and could not resist.
  23. ADV

    -5. stupid cold

    I have my trucks glow plugs wired up to a push button and it has been working great. I have the factory wate to start light wired in and I added a extra light on the hot side to know when the plugs are getting power. Kind of a safety to see if the solenoid sticks on like last time so l don't...
  24. ADV

    Aluminum injector caps

    Making a few 90 degree caps tonight.
  25. ADV

    Aluminum injector caps

    So far the caps on my truck are working great. They have seen about 100 degrees down to-7. I run my truck almost every day I have not touched them since I put them on. No leeks and now that I have good working glow plug system truck starts in a few seconds of cranking.

Latest posts

Forum statistics

Threads
92,932
Posts
1,155,156
Members
26,432
Latest member
pwillis

Members online

Total: 844 (members: 1, guests: 843)

Share this page

Top