Search results

  1. ADV

    INJECTOR PUMP IS LEAKING

    Can I put a turbo pump off of a factory ford turbo engine on my 7.3 NA? I have what i was told is a new pump
  2. ADV

    INJECTOR PUMP IS LEAKING

    baby moose would be nice buy running WMO would not be good for that pump I thought. There is another shop that quoted me 175 and it sounded like they know the old IDI engines.
  3. ADV

    INJECTOR PUMP IS LEAKING

    I just talked to a local injector repair shop and they told me the would put steel bushings in it and recalibrate the pump. Would cost around $550 if I took the pump off myself and brought it to them. I am starting to run a WMO mix so as long as its not going to hurt anything I think I will...
  4. ADV

    INJECTOR PUMP IS LEAKING

    I have a junk injector pump at home i took apart just to see how it works and there is an O ring on the shaft but I am not about to take the pump on my truck apart. Way to much to go wrong. I will look into the cover but I took that off again and put it back on and it was the same.
  5. ADV

    INJECTOR PUMP IS LEAKING

    I just turned up my fuel one flat this week and now my injector pump is leaking. When I idle up the truck and let it down fuel runs out of where the throttle shaft goes through the injector pump. This is a reman engine that I had in my fsuperduty its about 10 years old and around 40,000 miles...
  6. ADV

    auto locking hubs

    Last chance $35 shipped
  7. ADV

    FACTORY TURBO INJECTOR PUMP

    I will take a picture of the injector pump on my way to work today picture should be up tomorrow
  8. ADV

    FACTORY TURBO INJECTOR PUMP

    Factory turbo injector pump off of a 1993 f350. I was told it was new wen I bought the truck but I can not say for sure. Engine did run when it was pulled out. Also still have the factory turbo engine. Turbo and all parts for that are gone. $75.00 OBO feel free to make any offers
  9. ADV

    WTB. IDI turbo Injector line.

    injector line $20 plus shipping or I will bring it along with the springs if that deal works out.
  10. ADV

    1988 FSUPERDUTY parts

    I am in the Kiel area about 265 miles from you. If it works out we could meet some where a bit closer to you some weekend. JOHN
  11. ADV

    1988 FSUPERDUTY parts

    front and rear springs $150 Rear dana 80 complete with disks calipers $150 10 bolt rims 20 per rim 100 for the set doors in good shape for a WI truck Truck going to scrap in the next few weeks if anyone needs something let me know pedal assembly, hydroboost, engine and trans are gone.
  12. ADV

    voltage question

    I have just put a CB radio in my truck I have the positive wired to a wire behind the radio that turns on with the key. With the CB turned off if I turn the key to the on position my CB lights up for a second or two and shuts back off. I checked the wire voltage and right after the key is...
  13. ADV

    Just orderd a Centrifuge

    Running my first tank of the WMO mix. Once the truck is started it runs fine but the two cold starts not even that cold 40 degrees it started hard very hard!! I think I am just going to shut the truck down on clean diesel and switch it after the truck starts.
  14. ADV

    WTB. IDI turbo Injector line.

    I have a factory turbo engine I am parting. I have a line for you.
  15. ADV

    Need 7.3 dip stick tube

    I would ship it Monday morning, paypal is fine, P.M. me and we can go from there
  16. ADV

    Need 7.3 dip stick tube

    yes i do have one i would sell
  17. ADV

    Just orderd a Centrifuge

    Oil was up to 190 degrees when I got over to my parent place (that's where the setup is) got the pump hooked up and started up the 120 gph centrifuge. Ran it for 2 1/2 hours at 85 psi. I was to adjust the pressure relief so I can turn it up more I was told 120 PSi is fine for a inverted...
  18. ADV

    Just orderd a Centrifuge

    Maybe this weekend I will get this thing going thirds a charm right? I have a working electric motor now and the oil should be up to temp when I get up in a few hours then all I have to do is hook up a few hoses and start this thing up.
  19. ADV

    Need to find and install a 7 blade trailer plug

    I just buy the plug and wire it myself. I just cut into the wiring harness and add the wires I need. ON the truck I had now I had to remove the previous owners scotch locks I HATE THEM STUPID THINGS!!!!!!!!!!!!!!!!!!!!!!!!!!!
  20. ADV

    Need to find and install a 7 blade trailer plug

    Pollak makes a nice metal 7-pole plug for on the truck. That's what I use I got sick of braking the cheep plastic ones.
  21. ADV

    CB antennas on the mirrors

    I just finished up running the coax through the vent windows and hooked up power to the radio. But when I key up the mic and talk I can here myself through the truck stereo speakers. I have never had this I put the CB in this truck the same way as my last trucks. I bolted the antenna mounts...
  22. ADV

    Driveshaft problems

    i have a dana 80 rear from a 1988 fsuperduty. i have front axle and springs and maby drive shaft. i am in wisconsin around sheboygan if you are interested. John
  23. ADV

    CB antennas on the mirrors

    The last 3 IDI's I had with CB radios in them I had the antennas on the mirrors and ran the coax through the vent windows it works but is there a better way?
  24. ADV

    CB RADIO STUFF

    I had two trucks at one time but I went down to just having one so i have no need for the second radio. The mic is not with the radio but the radio worked fine when I pulled it out of the truck. how about $60 or reasonable offer I would like to get different antennas and some new coax cable to...
  25. ADV

    auto locking hubs

    Hubs 40 shipping included

Latest posts

Forum statistics

Threads
92,932
Posts
1,155,153
Members
26,432
Latest member
pwillis

Members online

Total: 958 (members: 7, guests: 951)

Share this page

Top