Search results

  1. Philip1

    ??? about throw out bearings

    Some (if not all) of the t-19 throw out bearings are greasable. None of the zf5 bearings are greasable.
  2. Philip1

    Stuck lower injector body

    If i remember correctly, I used a 5/16 bolt threaded into the center of the washer and used that to pull it out
  3. Philip1

    Radiator pressure

    Its possible the pressure you noticed could have been caused by changing ambient temperatures too. I have an old truck that just sits for the last few years and every so often I would check the coolant in it and without running at all it built a small amount of pressure to cause it to hiss when...
  4. Philip1

    Brake time. Hydroboost too??

    Many reman hydroboost systems do not come with the output shaft. There is a company on eBay that sells replacement ones but there are 2 types, big bore and small bore. I don't remember where the year break is for them though
  5. Philip1

    84 300td in a jeep looking for more power

    Thanks for the tip. I was unaware that any company offered bolt in turbos for these engines
  6. Philip1

    Need Suggestions/Advice on Rebuild

    Since you don't know anything about the truck and you'll have it torn apart, you might want to inspect your main and rod bearings to see if there are any excessive wear on them.
  7. Philip1

    Time for injectors, or is timing off?

    When I had issues with excessive smoke mixed with puffs of smoke I found i had a dead cylinder. It also caused the exhaust to smell like raw fuel as well. Not saying this is your issue, but it might not hurt to do a compression test on it.
  8. Philip1

    7.3 to 460

    The transmission bellhousing is different. If I remember correctly, you can redrill mount holes on a 460 transmission to fit a 7.3 but most likely not the other way around. Also the wiring harness would be very different due to the 460 being computer controlled (unless you are planning on going...
  9. Philip1

    Clutch question

    If it was me, I wouldn't reuse it. All those cracks in it would need at minimum a surfacing but most likely a replacement
  10. Philip1

    84 300td in a jeep looking for more power

    If I installed a 7.5mm injection pump where I would need a upgraded turbo, would a 7.3 idi factory turbo work well as a upgraded turbo?
  11. Philip1

    Crewcab Project

    man, I thought my truck got toasty...
  12. Philip1

    Hard starting issues still - air intrusion

    If you decide to replace the glow plug harness, you can either buy one from wes at classicdieseldesigns.com or build your own. If you build your own, you can use bullet connectors and 4mm (or 3.5mm for a tighter fit) silicone vacuum hose as a band to hold the connector to the glowplugs.
  13. Philip1

    Mini-excavator engine removal

    I heard somewhere that some rental places turn the hydraulic pressures down so the equipment doesn't get abused as bad
  14. Philip1

    Fuel leak drivers side

    The nickel/copper alloy lines are the best in my opinion due to the ease of use for bending with the proper tools and with the corrosion resistance
  15. Philip1

    Electric fuel pump part number

    I'm gonna be running the holley black fuel pump with a pressure regulator
  16. Philip1

    Small port hole under GP controller 7.3 IDI

    It isn't a true plug. Its hollow where the square hole is so it can hold tight on the valley pan but still allow fluid to flow through
  17. Philip1

    Small port hole under GP controller 7.3 IDI

  18. Philip1

    The right pre-charged anti-freeze

    https://www.amazon.com/Fleetguard-CC2602-Coolant-3-Way-bottle/dp/B01CPU734S/ref=mp_s_a_1_12?dchild=1&keywords=sca+test+strips&qid=1587743745&sprefix=sca+t&sr=8-12
  19. Philip1

    The Resurrection

    My air bags will have onboard air and a dual valve setup in the cab. It'll also have an exhaust brake thats air controlled.
  20. Philip1

    The Resurrection

    last but not least I started to pull the bed off but ran out of daylight and will continue tomorrow
  21. Philip1

    The Resurrection

    got the engine put together with .020 over pistons, ceramic coating on the pistons and flowcooler water pump got the ac and heater box replaced due to the old one being burnedgot the engine painted blue and blackdecided I wanted to install some air bags in the rear
  22. Philip1

    Promise... the build

    Keep us posted on how well it works in the long run. I never got the chance to do the long term testing on my truck before it burned.
  23. Philip1

    6.9 vs 7.3 Head Gaskets and Boost

    So when you modified the gasket did you just drill a hole in the gasket where the coolant passage is?
  24. Philip1

    Questions about Dana 70 wheel seals

    Almost looks like the only difference is the material being used. I cannot see why the one labeled for single wheel wouldn't work for a dually or vice versa. The difference between the dually inner vs outer almost looks like an error when the part number was inputed into the website. That's at...
  25. Philip1

    Questions about Dana 70 wheel seals

    Might wanna look a little closer at the part numbers. They both are 9864S

Latest posts

Forum statistics

Threads
92,932
Posts
1,155,156
Members
26,432
Latest member
pwillis

Members online

No members online now.
Total: 1,708 (members: 0, guests: 1,708)

Share this page

Top