Search results

  1. nhwrench01

    DB2 Fuel Intake Thread

    old post but, same here,, going the hardware store tomorrow for that same fitting...
  2. nhwrench01

    6.9 low power/no power.... need help

    p.s. truck is unloaded, 4x4 not engaged, running on clean diesel,
  3. nhwrench01

    6.9 low power/no power.... need help

    well i rechecked timing, was right on at 8*... i did back it off to 7* and went for a test drive to warm it up and see, if the grayish smoke and power was any different...,, about the same.. on the way back ( on a class 6 dirt road, hard packed dirt) i came to a dead stop, on a very slight...
  4. nhwrench01

    Dana 60 Axle shaft Seal Replacement

    when you are there, the axle will be mostly empty, ( pinion gear will be there ) but the ring gear and both axles will be out ( have to do this to replace axle seals) i run a rag and shop air to clean out dirt from the axle tubes, this might take some time to get them clean if you hit the mud...
  5. nhwrench01

    6.9 low power/no power.... need help

    i will recheck timing this weekend,,, ... what is the HPCA switch,, thinking the timing advance in the ip?.. ... i will report back after things are checked, working a 1/2 weekend .... But thank you for the help.. .
  6. nhwrench01

    6.9 low power/no power.... need help

    I have a gunson for the diesel and a timing light with a advance feature.
  7. nhwrench01

    6.9 low power/no power.... need help

    Kdo58… the lift pump is new. I know that doesn’t mean good, but with the old pump I had 2.2- 3.6 psi at idle. Now I have 4.5–5.5 psi… and it doesn’t die when the psi goes to 0, but this is at 2200-2300 rpm. 3/4 throttle and up hill… psi returns fast when I let off
  8. nhwrench01

    6.9 low power/no power.... need help

    The timing was off 7* retarted.. it did get very hot ( coolant) going up hills . And is now better. But very low power.
  9. nhwrench01

    6.9 low power/no power.... need help

    History on this truck, 1986 f350, (f250) badges. bought for a D.D. as my 93 350 7.3 has been retired.. so, the new truck , i have some paperwork with it, bought new by the ING corp, in Colardo, then in 2021 was in maine and registered with 245k on it.. i have done,,, used c6 trans (works good)...
  10. nhwrench01

    Blower motor

    If your talking about the blower motor( as the heading states ) id look at the resister and the plug to it,, with hi amps and time, the plug might be getting hot , slowing the voltage ...?? try unplugging the resistor plug,,, should be easy to pull off ( relatively)... look for the plug to...
  11. nhwrench01

    Air filter

    for me,,, id leave the stock filter and box on, that filter ( even with the air duct on) will suck in more hot air from under the hood than anything. the only aftermarket " cold air intake " types ive seen had a box around the filter with a tube or snorkel into the fender or behind the grill...
  12. nhwrench01

    oil filters on ebay,,,get them cheap

    wow, didnt know that,,, well i tried ...
  13. nhwrench01

    WMO Black Diesel - Cetane Number

    well said mt_man, but, alittle ( more like, ) way over my head. To the O.P.,, in the summer, i run used transmission fluid, not cut, straight, after 2-3 months of sitting and then filtered in a 1 micron sock filter, then right into the rear tank. sorry, started to rant abit,,, but my point...
  14. nhwrench01

    oil filters on ebay,,,get them cheap

    found some cheap oil filters on ebay today, a pack of 6 stp 3786 filters for 40$... i did run motorcraft 1997 filters, then the price and availability, left me looking for other options. i went with a napa gold 1734. now their prices went up too.. so, looking around i found these, there are...
  15. nhwrench01

    86, block heater question ,,

    nope, no big deal,,after all the work ive done on this thing so far,,, a block heater is not bad at all.. Bought it for a good price, ( for a running diesel in NH,) just some of the stuff but not limited too, front axle u joints, locking hubs,seals,calipers, used c6 transmission, deep pan,extra...
  16. nhwrench01

    86, block heater question ,,

    well, the block isnt cracked, but the heater is leaking some,,, sooooo,,,, looks like ill be changing that and doing the new radiator at the same time...
  17. nhwrench01

    86, block heater question ,,

  18. nhwrench01

    86, block heater question ,,

    ill look at that too,, thank you
  19. nhwrench01

    86, block heater question ,,

    from what i can see, drivers front by the injection pump, its 69d u2 d282974...
  20. nhwrench01

    86, block heater question ,,

    hhhmmmm,, dont know the serial number... ill have to look..
  21. nhwrench01

    86, block heater question ,,

    I was looking for first hand experience with people who use there block heater on their 6.9. my vin tag shows a build date of 12/85. I have looked at the block area of the heater and it does have the deep milled space by the dip stick tube and ( what i think ) is the thicker casting around the...
  22. nhwrench01

    Coolant coming from bottom of Radiator (only some of the time)?

    might be a " cold water " leak,, ive seen it many times. when things are cold, ( or at a certain temp,) things will leak. when it warms up, it will stop leaking. Thats the very basic idea of it,,, try checked all the hose clamps, keep an eye on things every now and then,,, it will start to...
  23. nhwrench01

    ATF in fuel filter

    Welcome to this great Forum. you will find lots of good people here with lots of good info.. if you could let us know what the issue is, what is or is not happening, and what you have tried, we could help better and maybe save you time and money. the ATF trick will work to help clean the pump...
  24. nhwrench01

    Another terrible loss..

    wow, very sad, great guy ,, he helped me with my turbo install on my non turbo, setting me up with parts i needed,,, sad to hear..
  25. nhwrench01

    Atf and wmo mix

    see some of my other write ups about running atf.. i tried wmo for a while but, it didnt work so good for me,, using atf worked great... it will take me to long to recall my findings, but i did do some write ups on how and what i did, the 93 is now a plow,yard rig, due to rust and the e4od is...

Latest posts

Forum statistics

Threads
92,565
Posts
1,149,821
Members
25,772
Latest member
Briarpatch

Members online

Total: 675 (members: 9, guests: 666)

Share this page

Top