Search results

  1. S

    Squealing Noise Until Operating Temp

    @rvitko Thank you for the reply. Does your squealing also stop whenever you get near operating temp? Is cold up here so mine never warms up to that point idling, have to drive it and it lasts for miles but it would at closer to sea level warmer places.
  2. S

    Squealing Noise Until Operating Temp

    @Lumberjackchuck I have not but I will try that. Thanks
  3. S

    Squealing Noise Until Operating Temp

    Also the 904-807 Dorman vacuum pump has been discontinued and is very hard to find now. I have one on the way but it’s not going to get to me till Christmas. The one I had on there was a Amazon one and I have no idea if it’s quality or not.
  4. S

    Squealing Noise Until Operating Temp

    I also do not have an ac, pick up did have one but has a bypass pulley now.
  5. S

    Squealing Noise Until Operating Temp

    1993 F250 7.3 IDI 4x4 zf5 non turbo Merry Christmas and Happy late Thanksgiving to you all. I have had a problem with a squealing noise from this pick up since very recently after replacing the transmission and main seal for the last time. It happens only while driving and I don’t think it’s...
  6. S

    Fel Pro Rear Main Wear Sleeve

    The Fel Pro rear main seal with the sleeve fixed my leak. Thanks again for all the help.
  7. S

    Fel Pro Rear Main Wear Sleeve

    Thank you all for the replies. My flywheel came with the new bolts with pre applied thread sealant, it leaked then and when I put lock tite on it. There were no signs of oil coming from the crank’s threads. From what I could tell each time there was oil coming out of the bottom of seal where...
  8. S

    Fel Pro Rear Main Wear Sleeve

    I decided to just take the sleeve out of the seal. It wasn’t as stuck in there as I thought, was probably just too worried about it. I’m going to assume it was just in there to protect the seal during shipping and go ahead with install. Pick up has to drive 8 hours or so on Friday but I’ll just...
  9. S

    Fel Pro Rear Main Wear Sleeve

    I just don’t understand how that sleeve is going to go over the crank whenever seal is pressed into plate and then I attempt to install over crank. My first thought was to install plate and then drive seal in with the sleeve but that seems wrong too and likely to mess something up. Maybe that...
  10. S

    Fel Pro Rear Main Wear Sleeve

    To be clear on my other two seals they were installed as described above. Clean crank with no gasket maker or oil of any kind.
  11. S

    Fel Pro Rear Main Wear Sleeve

    @IDIBRONCO I promise you that sleeve is made of metal. This is the one I have. https://www.napaonline.com/en/p/FPGBS40697?ir=2&r-src=BR:PDP:SP:Aboveproductdescription&ppid=FPGBS158681
  12. S

    Fel Pro Rear Main Wear Sleeve

    1993 7.3idi non turbo, Zf5-47, 4wd Rear main seal started leaking again, from where the seal meets the crank. I spoke to someone who builds powerstroke engines and he suggested I should get one with a wear sleeve even though there is no obvious groove or wear on the crank. The only one I can...
  13. S

    Zf5 Rebuild or Replace

    An update and info for anybody doing a similar project. The Zf5 47 fit right in and seems to shift great. I got the transmission from A1 Transmission & Parts in Denver. Will and his staff there seemed to know their stuff. I also did the rear main seal and got the new and “improved” seal from...
  14. S

    Slave Cylinder Bleeding Trouble

    Thank you all again for the advice I was able to find a full system pre-filled on Labor Day. I kind of wish I would’ve waited because the one I picked up from Oreillys has a very differently shaped hydraulic hose and runs closer to exhaust, steering column and rubs on my brake lines but it...
  15. S

    Slave Cylinder Bleeding Trouble

    1993 F250 7.3 idi zf5 4x4 NA Howdy, thank y’all for your help with the ZF5. I installed the 47 on Friday/Saturday and went great. Haven’t shifted it yet but will update other post when I do. While I was dumb***ing about getting it installed I wanted to start pick up to check if my rear main...
  16. S

    Zf5 Rebuild or Replace

    @amsmith That is a great idea I will start doing that, thank you. @Nero that’s what I was hoping when I first saw it but it is cracked, all the way through. Enough to leak fluid on the outside of the case. The crack goes out to where the transfer case linkage bolts up. @KansasIDI Thank you...
  17. S

    Zf5 Rebuild or Replace

    @IDIBRONCO its a little flat in Texas for me. I was living in Oregon for a bit and I didn’t notice any difference around 4-5,000ft but here in Colorado now and the performance of mine is definitely diminished. What bugs me maybe the most is how long it takes for oil pressure to drop after cold...
  18. S

    Zf5 Rebuild or Replace

    To be clear the case is only cracked in one spot all the way through, at least to my knowledge. I planned on use some dye penetrant to fully inspect it.
  19. S

    Zf5 Rebuild or Replace

    1993 7.3 idi NA non turbo, 4wd single cab Howdy hope everyone is running well. I removed my zf5 42 transmission with the intention of rebuilding it. Had very slow, notchy, double clutching shifting since I got it but on my last drive across country it got really bad, I assumed this was due...
  20. S

    Gear Rubbing Inside of Manual Hub

    @Rdnck84_03 There is definitely some play in the axle shaft/knuckle. I figured it was the u joint. It is much worse on the driver side though, one with no noise when turned. Was going to replace that when I can purchase tools for it. So there is a third bearing on the inside side of dust cover?
  21. S

    Gear Rubbing Inside of Manual Hub

    Also only makes this noise when turning the hub/rotor backwards, whenever turning forward there is no noise.
  22. S

    Gear Rubbing Inside of Manual Hub

    1993 F250 7.3 NA with Dana 50 and manual locking hubs. I just replaced rotors, calipers, brake pads, and bearings/races. When I put the hub back together on the passenger side the larger gear that is inside the hub body/ backed by a spring and held in by a small Phillips screw is rubbing and...
  23. S

    Spindle Nut Socket Size?

    This one worked for me. Size is 2 5/8th 4 lug part #: pt w83010...
  24. S

    Blinking Fuel Filter Light

    @Clb I have a 93 7.3 idi na ZF5 transmission. Everything that I’ve replaced has been oem/stock equivalent besides baby moose injection pump. Got the lift pump from Napa I think it was made by Carter (?) can’t remember name of it. I have replaced fuel selector valve and it is working, not...
  25. S

    Blinking Fuel Filter Light

    Also replaced both shower heads and cleaned out rear tank recently. Did the front tank something like a year ago.

Latest posts

Forum statistics

Threads
91,904
Posts
1,140,006
Members
24,724
Latest member
tannermorris

Members online

Total: 349 (members: 5, guests: 344)

Share this page

Top