1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

Recent Activity

Activity stream for all registered members at Diesel Truck Forum - Oilburners.net.

  1. david85 liked IDIBRONCO's post in the thread Bullnose/Slantnose Diesel Picture Thread.

    Here's a picture of the "twins" This was while I was hauling off the Bronco to get rid of it. [ATTACH]

    293.JPG Sep 17, 2019 at 1:02 AM
  2. Shamoke replied to the thread Brand new to the fourm...Have a question.

    Thank you very much for the info, it will help. I've seen videos about newer Powerstroke engines and testing for blow-by by loosening...

    Sep 17, 2019 at 12:59 AM
  3. jetfly12 attached a file to the thread Project Dirty Diana.

    Just pulled the Eisenhower grade at about 12.5k gross on Saturday. This is the 4th time I have pulled this hill with my idi and all I...

    20190913_182556.jpg Sep 17, 2019 at 12:50 AM
  4. lotzagoodstuff liked janssen's post in the thread WMO in CRD, Test in progress - any others using WMO in CRD?.

    Update - so ran about 7K so far and all is good - except one small issue. I wont start worth a crap on straight W85 tip start takes 3...

    Sep 17, 2019 at 12:45 AM
  5. lotzagoodstuff replied to the thread Brand new to the fourm...Have a question.

    I would call and tell the owner you want it cold to start it when you get there. I think you can tell a lot more starting one cold than...

    Sep 17, 2019 at 12:40 AM
  6. 79GLIDE replied to the thread '94 IDIT runs rough, low power, nearly overheating after Moose IP.

    I'll just throw this out there, but besides the previously mentioned valve train concerns, what about the condition of the camshaft?

    Sep 17, 2019 at 12:38 AM
  7. lotzagoodstuff liked Thewespaul's post in the thread '94 IDIT runs rough, low power, nearly overheating after Moose IP.

    Most likely a rod bearing on the big end, since bearing wear opens up the oil tolerance, the piston can travel down and up further in...

    Sep 17, 2019 at 12:25 AM
  8. Shamoke replied to the thread Brand new to the fourm...Have a question.

    So I'm feeling a bit more confident in the ability of this truck thanks to your replies, thank you. Any advice on what I should look for...

    Sep 17, 2019 at 12:20 AM
  9. 79GLIDE replied to the thread Brand new to the fourm...Have a question.

    I'd do it. SE MO hills can be a bear, but with the 5 speed you should be good to go. The pic in my sig is my 1990 F250 7.3NA E4OD 4X4...

    Sep 17, 2019 at 12:14 AM
  10. Greg M posted a new thread.

    Injectors

    Hi all new to forum from Australia with my trusty Dually , have 88 f350 7.3 idi 85,000 miles running rough so pulled an injector out ,...

    Forum: Introduction

    Sep 17, 2019 at 12:10 AM
  11. Shamoke replied to the thread Brand new to the fourm...Have a question.

    It's listed as having a ZF-5 Speed Manual Transmission. I'm not going to try to race I just want to be able to haul. local area would be...

    Sep 17, 2019 at 12:03 AM
  12. Selahdoor liked IDIBRONCO's post in the thread To continue project or??.

    Sounds like incentive to get it done quickly.;)

    Sep 17, 2019 at 12:01 AM
  13. Selahdoor replied to the thread '94 IDIT runs rough, low power, nearly overheating after Moose IP.

    Good thing I found out NOW!

    Sep 17, 2019 at 12:00 AM
  14. Selahdoor liked D_Fresh361's post in the thread So what did you do with your truck today?.

    We are in the same exact boat! But I know she’s in good hands so it helps me sleep, a little. Lol

    Sep 16, 2019 at 11:58 PM
Loading...