Recent content by Giddy-Up

  1. Giddy-Up

    So What Did You Do With Your PSD Today?

    Did a little trimming for the air compressor.
  2. Giddy-Up

    7.3 PSD Up-pipes

    SOLD
  3. Giddy-Up

    Dana 60 Knuckles

    I'm looking for a set of the later style ~95-97 Dana 60 knuckles with the bolt on caliper mounts, NOT the slide pin style. Thanks
  4. Giddy-Up

    Vacuum block for a 1995 7.3 powerstroke

    Still need one?
  5. Giddy-Up

    7.3 PSD Up-pipes

    I've got Irate diesel bellowed up pipes that I never used before deciding to go with a different turbo setup. I'd like to get $500 for them since they're unused, they sell for $600. I'm not on this site very much, but i'll try and check though. Text would be best. 701-263-1040
  6. Giddy-Up

    So What Did You Do With Your PSD Today?

    Got my fuel tank mounted up, hangs down 3" more than the old tank but the suspension sits ~7" higher than factory. Kind of wish I went deeper.:dunno I got a couple odds and ends to do then the box should go back on tomorrow.
  7. Giddy-Up

    What does your OBS weigh?

    I'll have to do that, should have the box on and be driving it again tomorrow.
  8. Giddy-Up

    What does your OBS weigh?

    I've been doing some thinking lately about just what a OBS can handle. I know there are tons of threads about "how much have you towed" but I'm curious what the pickup and trailer weigh combined. Some pickups weigh a lot less than mine and there are ones with service bodies that weigh more...
  9. Giddy-Up

    So What Did You Do With Your PSD Today?

    Got the majority of my fuel tank welded up, still have to make the mounts and pressure test it. Overall it came out pretty good, some of the welds aren't the best looking but I was more focused on sealing than looks.
  10. Giddy-Up

    So What Did You Do With Your PSD Today?

    Managed to make a little progress on my tank, after finishing a side project for a friend.
  11. Giddy-Up

    So What Did You Do With Your PSD Today?

    Did some little stuff. Made a new handle for for the gooseneck, got the metal for my tank, started butchering the donor tank. The sending unit mount is going to be easier to transfer than I thought. I also figured out why these tanks are such a pain in the a$$ to fill. Never knew the fill tube...
  12. Giddy-Up

    So What Did You Do With Your PSD Today?

    A sump would be easier, but to me it seems like it would draw more debris into the lines. Especially on a fabricated tank since there's sure to be some crap in it as the mill scale flakes. But I'm paranoid about stuff like that. :dunno
  13. Giddy-Up

    So What Did You Do With Your PSD Today?

    Yup, built about a dozen or so at my last job so I'm practiced. Going to use the pickup and sending unit out of a bronco, that way the gauge still reads correct.
  14. Giddy-Up

    Suggestions for tow rig tire...

    Firestone Transforce A/T, Cooper AT3, or Hankook RF10 or RT03 if you want more grip. I personally run the Hankooks RF10, but I put all three on customers vehicles all the time and haven't had a complaint.
  15. Giddy-Up

    So What Did You Do With Your PSD Today?

    The hitch is finished finally I welded everyplace I could, the main cross bars are 1/4" wall plated with 1/4" plate. Decided on the rear fuel tank dimensions and it should be about 45 gallons, depending on how deep I make it.
See more

Latest posts

Forum statistics

Threads
91,262
Posts
1,129,488
Members
24,091
Latest member
freqencyheight

Members online

Total: 544 (members: 1, guests: 543)

Share this page

Top