Recent content by aofarrell2

  1. A

    Excessive oil consumption

    I run 15w40 Delo or Northland conventional oil, both are CK-4 rated oils. As far as conditions, oil consumption increases with engine speed. Interstate driving vs highway is noticeably different for consumption. Never heard of this AutoRX stuff. Where do you guys get it?
  2. A

    Excessive oil consumption

    Sooo... Been burning a LOT of oil in my '92 7.3 IDI (non-turbo). I'm going through a gallon of oil every 250-300 miles, sometimes more. But it's not really smoking blue at all, and it isn't leaking more than a drop or two. Truck starts and runs decent. I've got to figure this out because it's my...
  3. A

    EC-1 coolant in IDI?

    Part of the reason I'm hoping to run EC-1 is it's hard to find green coolant that's SCA-compatible (not all green coolants are made the same!). I've seen a few that explicitly say they are NOT compatible with SCA additives. Not sure what makes them incompatible with SCAs but it would just be...
  4. A

    EC-1 coolant in IDI?

    I've seen various scattered threads on this subject but not a whole lot of helpful information. I can readily get Cat EC-1 coolant and I would prefer to use it if I could, as it's premixed and has cavitation protection, plus it's only like $13/gallon for 50/50 premix. My copper radiator is...
  5. A

    E4OD torque converter lockup issues

    Let's hope it's not a **** kit sorry, couldn't pass that opportunity up. On another note, drove the truck 200 miles today, and noticed a random quick unlock and locked back up again. Im suspecting one of two things. Each time I turn on the turn signal it messes with lockup. Either my MFS is bad...
  6. A

    E4OD torque converter lockup issues

    Figured out the lockup issue. I was aware of LEDs causing issues. I didn't think this truck had LED lights on the rear as they looked like incandescent housings and lenses (you know how you can usually see the LEDs clearly). Well I figured I should check and see if a filament collapsed in a...
  7. A

    E4OD torque converter lockup issues

    Well I installed a new FIPL and adjusted it to read 1.2v KOEO at idle. Shifts are still on time but lockup still only occurs with throttle nearly to or at the floor. As soon as I let off the throttle to less than 80% or so it unlocks immediately. Any ideas? Should I change the voltage and play...
  8. A

    E4OD torque converter lockup issues

    Yes the Rear ABS light is illuminated. Tach works and is never erratic. What recall are you referring to? I was not aware of one for the cruise control.
  9. A

    E4OD torque converter lockup issues

    The brake lights work and the switch appears to release properly. I should also mention that the cruise control doesn't work either, I don't know if that's related or not.
  10. A

    E4OD torque converter lockup issues

    Working on my new to me 1992 F350 with a IDI and an E4OD, and having some issues with t/c lockup. Transmission has clean fluid at the correct level. Shifts fine and for the most part shifts are on time, although there is an occasional erratic downshift when lightly applying throttle and then it...
  11. A

    Weird glowplug issues...

    I don't seem to have that 10 or 12 wire plug. The glowplug feed comes directly off of the starter relay, and that connection and wiring seems to be in good shape. All of the GPs are at 0.4-0.5 ohms so no open circuit, and yes there is 12v at each plug. I'm going to pull one of the plugs next...
  12. A

    Weird glowplug issues...

    Yes I checked, every glowplug has 12v with the relay on.
  13. A

    Weird glowplug issues...

    So I should start by saying I just got this truck recently, and I don't know much about it other than the original owner took good care of it (maintenance records) but the person who owned it before me was a complete idiot. That being said... I am having the most frustrating issue with the...
  14. A

    Box on C&C

    Appreciate all the info! I've been looking for a box but so far nothing decent as far as rust goes. I may end up keeping the flatbed for now, although it needs to be re-worked if I do as it's designed for a SRW (previous owner ran without the duals, no clue why).
  15. A

    Box on C&C

    So I just picked up a 1992 F350 today. So happy to have an IDI again. The truck is a flatbed, and I believe it is a cab and chassis, especially after seeing a incomplete vehicle tag of sorts in the original paperwork that came with the truck. My question is, I would like to put a proper truck...
See more

Latest posts

Forum statistics

Threads
91,262
Posts
1,129,488
Members
24,091
Latest member
freqencyheight

Members online

Total: 565 (members: 1, guests: 564)

Share this page

Top