Search results

  1. E

    Large Capacity rear fuel tank

    I received the 38 gallon tank from LMC, as it turn out it is Not made with plastic, it is a galvanized tank. I received mine with the extended mounting hardware kit a pick up seal and extensions for the pick up tubes. I brazed the extensions and installed the new tank with a new sending unit. I...
  2. E

    Large Capacity rear fuel tank

    this one right here http://www.lmctruck.com/icatalog/fd/full.aspx?Page=41
  3. E

    Large Capacity rear fuel tank

    I ordered the 38 gallon plastic tank from LMC, it comes with an extension kit for the pick up tube so we'll see if that works or I might just braze an extension. I hope it fits an will take some pics and upload them if possible.
  4. E

    Large Capacity rear fuel tank

    Thanks everyone, I found a few threads but all seemed to have pieces of information, but I think I remember reading the article about a 38 gallon tank but there was an issue with the fill tube or something, also the one I remember was plastic. The one on My truck needs to go so I thought what a...
  5. E

    Large Capacity rear fuel tank

    Hello everyone, there used to be a thread in the archives on how to install a new plastic fuel tank I believe from a bronco. I would appreciate if someone can point me to that thread if it is still available, I've searched for it in the archives and IDI forum but only find similar with out part...
  6. E

    Clutch slave bleeding problems

    The pedal is too soft to pump it the normal way, he can easily pump it by hand (all parts are now new he bought the entire master/slave kit and the pedal is working fine) several times then hold it for me to crack the screw open enough to blow some fluid then do it all over again but we cant get...
  7. E

    Clutch slave bleeding problems

    Yes I called it pin but it is in fact a Allen screw. I though after many times it would start making progress I've done a few already but this one does not make progress other than an inch of travel and never really gets to push any harder. I even tried pulling it out turn it where the air would...
  8. E

    Clutch slave bleeding problems

    Hey guys, long time again, hope all are well. A buddy of mine as asked me for some help with His 94 DI ford with a ZF manual transmission. The original slave cylinder cracked and he bought the complete assembly broke the plastic clip holding the rod when installing it and now has almost no...
  9. E

    Ring/pinion

    I'm not in a rush to do it but I do want to make the switch, the cummins has a lot of low end torque it doesn't need the 4.10 and I have low 4wd if I needed it. Let me know if You want to swap them.
  10. E

    Ring/pinion

    I did the all new bearings on My D60 front and set the gears, it worked great since but then again I don't drive on 4wd all the time. For the rear axle I'm not sure I have the skills yet so I want someone who does to do it for Me, I might take the advice given here and find a 3.55 complete rear...
  11. E

    Ring/pinion

    I'll try to keep what I have, I just want higher gears, there has to be someone around here who can do it. I saw a thread You started about Your shop, it looks great, I like how You mounted the gypsum to the ceiling.
  12. E

    Ring/pinion

    Joe!!! we are not far at all, I moved to Frederick a few years ago, still with chimneys just no masonry anymore. I few years back I got my license for HVAC and I've been doing it since, I do all the inspections and carbon monoxide test for the chimney company when they install a liner. I have...
  13. E

    Ring/pinion

    For a while now I've wanted to have 3.55 gears on My truck instead of 4.10's , I do not want to take my truck to a shop but I'd like to bring it to someone Experienced who can do it for Me. I'm in Frederick in case someone near me is available. Thanks.
  14. E

    Rims and headlights

    Been trying to get rid of this but it is taking space here if I don't sell it I'll have to scrap it.
  15. E

    Rims and headlights

    Alright, let Me make it interesting. I will include a 84 pickup front bumper in good usable condition and a Mitsubishi starter (almost new) and a set of brand new rear brake shoes for a f250 (I ordered them by mistake and never used them) plus what I posted earlier all for $100. Come and get...
  16. E

    Rims and headlights

    Too much? I have also a set of 8 used injectors from My plow truck that I replaced with rebuilt injectors from Mel. Come and get it all for the same price.
  17. E

    83 W350 Crewcab Project

    I'm glad to see the project is going forward Billy. There should be some 80's dodge with a good roof near FL, still I like the look on that truck.
  18. E

    Rims and headlights

    I have 2 steel DRW truck rims and two head lights with hardware one is very nice and the other one needs a polish all this fits a OBS ford 91-97. Local pick up only $40 for everything. Thanks.
  19. E

    Still in the IDI World for a Short While Longer

    It's been a long time no doubt. I didn't read the rest of the thread but I read the first one, You don't mention if You replaced the water pump, maybe something to look into.
  20. E

    Best EGR delete kit and tuner?

    Here is more information. I went back to the site I was going to purchase from, they have 3 separate kit for the egr delete, I want to get this one "http://www.mkmcustoms.com/basic60powerstrokesolution.aspx" but they also offer this one...
  21. E

    83 W350 Crewcab Project

    That is a beauty Billy, I read of many doing swap and it sounds very easy compared to others. You can't go wrong with a p-pump and nv4500. Having the option I would go with 3.55 gears.
  22. E

    Best EGR delete kit and tuner?

    I have intentions of doing this for a couple of years now, last time I checked the sinister kit looked the best, however I wont be doing the HG they appear to be fine and I don't tunes for it. Hope to do this soon if I have the time, I remember someone in VA was doing this at a shop can't...
  23. E

    Site Ownership >>>SHAGGY<<<

    Thank You for everything, I appreciate it.
  24. E

    Clutch HELP!!

    Are You doing this alone or You have someone help You? Is the slave the kind with a small Allen screw? In My experience all it takes is a few pump and then let a small amount of fluid out, notice there should be more air than fluid coming out, all this while the push rod is properly installed...
  25. E

    WTB 1976 shifter

    Looking to buy a shifter with a knob in nice shape (not scratched off or beat up) for a 1976 ford with a divorced np205, I tried buying new but LMC doesn't list it (or I can't find it) and every one else wants to sell Me a twin stick :dunno. Also I'm looking for a OBS shifter boot in great...

Latest posts

Forum statistics

Threads
91,280
Posts
1,129,752
Members
24,098
Latest member
William88

Members online

Total: 481 (members: 7, guests: 474)

Share this page

Top