Search results

  1. B

    04 P0087 and surge at idle

    My sister in laws 04 duramax has been setting a p0087 and surging at idle. She describes it as sitting at a stoplight and it tries to take off on her. She had someone tell her it was the FPR, but I am seeing people talking about fuel lines colapsing, bad injectors, and an occaisional FPR. I am a...
  2. B

    Heater coil hose (tee)

    Heater CORE. Just nitpicking.
  3. B

    Coil springs

    I have worked for a couple alignment shops that had the equipment to bend the I beams to adjust the camber. Might be hard to find a shop thT has the equipment and someone that knows how to use it but maybe a tire and alignment shop that has been around a long time could do it.
  4. B

    Rebuilding front end 93 f250 dana 50

    That universal very rarely goes bad. I would not consider replacing it as maintenance. Is it bad?
  5. B

    starter needed, which type?

    I put one of those on in November, it worked fine at first, but now when hot it sometimes just clicks when I try to crank it. Usually starts on the second or third time, a couple times it took 6-8 tries. I haven't inquired about getting it warrantied yet.
  6. B

    LIFT PUMP BLOCK OFF PLATE

    Edit: I tried to quote Gary's post about using the gasket as a template before my post. That's what I did, but I didn't want to use a paper gasket as I trust ultra black more. I went to autozone and asked them to see a lift pump for my idi, took the gasket out and made a tracing of it to make...
  7. B

    Fuel Heater Leaking

    I used a little blue loctite. Hasn't leaked in 6 months or so.
  8. B

    Front Rotor Replacement

    Two or four wheel drive?
  9. B

    Separate Brake and Turn Signal Lights

    That's to go from 4 lights to two, not the other way around.
  10. B

    Separate Brake and Turn Signal Lights

    I'd want to study the wiring diagram to be sure, but you should just be able to come straight off the brake light switch to those lights, then use the factory wiring to go to the turn signals.
  11. B

    U Joint How to?

    Be careful with a ball joint press. I have seen a couple driveshafts get the ears bent with a ball joint press.
  12. B

    Mag-hytec diff cover

    Put studs in those two holes, tighte a nut down on it with enough stud left to space the bracket out... Might work.
  13. B

    088 pedestal to valley pan grommet

    Does the felpro box list the individual part no.s for the contents?
  14. B

    comments about your ZF5 failure

    I've got one with a broken ear at the trans mount. Reverse synchro is a common failure.
  15. B

    ZF drain bolt seized

    The drain plug is definitely steel
  16. B

    ZF drain bolt seized

    I'm a little late to the party, but you could have just removed the pto cover to drain the trans.
  17. B

    Schrader valve alternatives

    Doesn't it suck air in when you hold the Schraeder valve open without cranking the engine? If I'm right on that youd get air in it when you stop cranking and walk around the truck to close your bleeder
  18. B

    Swapping motors. Any tips?

    I usually just let the air out of the tires. Makes a huge difference.
  19. B

    Swapping motors. Any tips?

    I'd replace the orings in the oil cooler while the engine is out. When I did mine I removed the hood and rad, but not the core support. Remove the oil filter before you try to pull it.
  20. B

    PSP for a Hydroboost setup

    I've heard Saginaw pumps are the hot ticket, I'm not sure why though...
  21. B

    Electric plug on top of fuel heater *removal?*

    I removed my heater when it started leaking. Tapped it to 1/2" pipe thread.
  22. B

    For all of the alignment experts out there...

    The suspense is killing me. What did you find out with the caster and camber?
  23. B

    Regearing a ZF5

    Do you know that you can redrill the bell housing on a 460 trans and bolt it to a diesel?
  24. B

    Minimum brake shoe thickness?

    Iirc, wv and va state inspections say 3/32 or less fails. I have measured shoes new in box at 3/32 to tbe rivet head.
  25. B

    Engine Hoists

    I think the op'er said hes doing this on gravel. One more reason not to use an engine hoist.

Latest posts

Forum statistics

Threads
91,280
Posts
1,129,765
Members
24,098
Latest member
William88

Members online

Total: 635 (members: 8, guests: 627)

Share this page

Top