Search results

  1. 02x72

    Leece Neville Problem

    The Leece on my 93 F350 stopped charging, and I'm new to these units. I know that it is internally regulated and are pretty bullet proof, but is there an easy way to tell if the regulator went out on it since that's a much cheaper repair. I'm getting no charge off the positive terminal, but if I...
  2. 02x72

    Baumann/ US Shift Controller

    You can basically fully customize your transmission. Shift points, line pressure all sorts of stuff. It acts as a diagnostic tool giving you an error codes, displaying trans temp, speed, rpm and all sorts of stuff. It's surprisingly really easy to use. I would drive down the road with the...
  3. 02x72

    Baumann/ US Shift Controller

    Had installed on my truck, for E4OD transmission, comes complete with wiring harness for that, CD to load onto your computer to control it, and cord to sync unit and a computer. In great shape, only used for about 2 months really before I had to park the truck a year ago. Only selling because I...
  4. 02x72

    sterling axle question...

    I have one, but the truck was originally a C&C truck, not sure if they ere maybe optioned differently?
  5. 02x72

    86 F250 C6 is out. Need advice, rebuild tranny for same price as Zf5 conversion

    Not sure if it helps, or where in WI you are, but if you want to drive to Des Moines I have a good C6 you could have for free. Its going to scrap soon since its just taking up space.
  6. 02x72

    New E4OD test run, help with shutter

    Finally got my new Baumann controller in, which is sweet btw, but have a few issues. First, there is a very notifiable shutter when accelerating though first and second gear, then a horrible one when I get to about 60. All of the shifts are very very firm, but that could just be a tuning issue...
  7. 02x72

    FILP Wires

    Got it, thanks guys
  8. 02x72

    FILP Wires

    Im installing my new Baumann controller and am hooking up the FILP wires, but the new clip from napa just has three white ones. I found a while ago a page telling which ones they are, but cant find it. Can anyone tell me which is the ground, feed and output signal on the sensor. Maybe in a...
  9. 02x72

    Bench Bleeding Master Cylinder

    I ended up getting it. The whole keep it level thing is a load of crap. Once I took it out of the vice and started pushing the MC in with it at all different angles it worked. Thanks for the help guys
  10. 02x72

    Bench Bleeding Master Cylinder

    I thought the plastic plugs would be a problem as well, so I installed brass plugs nice and snug into the ports. After a few strokes the bubbles stop but it still wont build resistance. Each time the stroke gets a little shorter, then just stalls there
  11. 02x72

    Bench Bleeding Master Cylinder

    For the life of me I cant get this damn thing to bleed. Two from Napa, and one from Orileys and they are all doing the same thing. won't build up pressure on the bench, and when installed the pedal has no resistance. All of them were new, not rebuilt. I am replacing it because the old one is...
  12. 02x72

    7.3t engine removal questions

    Last time I pulled the engine on my truck, I took the front tires off and supported it to where the rotors were just off the ground. I feel it helped a ton getting the 7.3 over the core support, and doing it by myself it definitely made me breathe a little easier having that extra foot to work...
  13. 02x72

    help me design my new electrical system

    This is all I have for now. I found it easier to make a complete list, then break that down into smaller chunks to do. For instance, I ran a ground for everything I would need, then constant hots, then 12v switch hots, ect. Dont make fun of my setup lol, it orks perfectly. I needed something...
  14. 02x72

    help me design my new electrical system

    Oh and label EVERYTHING. I used one roll of 500' of black wire for everything, so if you dont have it labeled when you walk away from it good luck figuring out easily. I used Romex sheathing around the end of the wires since I use the stuff everyday and have an unlimited amount.
  15. 02x72

    help me design my new electrical system

    I just re-wired my entire truck. Built a box in the engine bay that holds all of my relays and fuse block. Everything in there is nice and neat, and easy to navigate. I used these relays http://www.amazon.com/Genssi-Relay-Harness-Bosch-40AMP-HRNS/dp/B00CUKXODI and they seem to be working well. I...
  16. 02x72

    c6 to E4OD transmission swap

    That makes sense. Sure works out nicely for me.
  17. 02x72

    c6 to E4OD transmission swap

    Im just wrapping this swap up, just need the baumann controller to get it on the road. Had to shorten the front shaft by 4 1/4" for it to fit. I was able to re-use the E4OD crossmember and drill new holes for that. If you dont have E4OD cooler lines you will need to cut the rear on from your C6...
  18. 02x72

    Tach Sensor Fix!

    Oh, well I didnt find anything. Either would work I guess. Like I said I wasn't just my idea.
  19. 02x72

    Tach Sensor Fix!

    Ive been thinking about a way to fix the Ford sensor first, but that was a bust. The when I was replacing the CPS on my dads excursion I noticed that it was a magnetic sensor, just like my tach. It obviously couldn't be made to fit, so I started looking for something that would. I did some...
  20. 02x72

    Tach Sensor Fix!

    So as we all know our tach sensors are prone to having the wire sheathing split as it enters the sensor and leaving us with no choice but to head down to the dealer and bend over for a new one. Well not any more guys! In a effort to fix my intermediate tach, I set out to find a better way to do...
  21. 02x72

    Tach Sensor Wire colors

    hmm, maybe theyre just really faded and I cant see the tracer colors or something. I guess Ill just start hooking them up and see if any of those combos work. Thanks for the input guys.
  22. 02x72

    Tach Sensor Wire colors

    Neither one of those wires is in there. I followed it back and have narrowed it down to some combo of a green/red wire, black, and blue. Can anyone confirm on their truck if there are correct?
  23. 02x72

    Tach Sensor Wire colors

    Ok, Ill see if I can fine those tomorrow and maybe trace them out. Thanks for the help
  24. 02x72

    Tach Sensor Wire colors

    Sorry, its a 1989 f350 harness
  25. 02x72

    Tach Sensor Wire colors

    Somewhere along the line in my rewire of the truck I cut the tach sensor wires on the harness. I cant find them, but have access obviously to the main harness. Can someone tell me what colors they are just past the connector, Ive searched and come up a few different answers. Thanks guys

Latest posts

Forum statistics

Threads
91,280
Posts
1,129,764
Members
24,098
Latest member
William88

Members online

No members online now.
Total: 623 (members: 0, guests: 623)

Share this page

Top