Search results

  1. UMR_Engnr

    So what did you do with your truck today?

    Found these door latch striker bushings on Amazon. The ones on my truck (1989 F350) had long since disintegrated. Nice and quiet now.
  2. UMR_Engnr

    Zombie Slayer: New Fuel System

    I haven't been around in a while, but I'm hoping to tear into my truck this year and get my M101 trailer bed on. With my bed off I'm going to be redoing all the fuel system. My rear tank has rust in it, so I've got new MTS tanks poly tanks. Also, the pickup was broken on both so I'm going to...
  3. UMR_Engnr

    Low Frequency Vibration

    My daily driver needs repaired so I've been driving my truck quite a bit. I noticed about a month ago that if I applied a little gas off idle it would start making a vibrating noise. It has gotten worse so that now sitting at idle there is a low frequency vibration and noise and it is just...
  4. UMR_Engnr

    Tire balancing beads

    I've had Dyna beads in my 33" Goodyear Duratracs for a few years. I don't often get above 60mph, but it drives smooth.
  5. UMR_Engnr

    MEP701 Military Generator

    Sold
  6. UMR_Engnr

    Bought one! Now to drive it 600 miles

    I second the shower head issue. When I drove my truck back from Texas (560 mi) it died on the highway an hour from home with 1/4 tank left. We were so close. I decided to switch tanks and crank away. Eventually it came back to life. So keep the fuel topped up. To aid in priming the fuel...
  7. UMR_Engnr

    4 plugs give ohm reading but front and back two don’t

    Got it. Thanks.
  8. UMR_Engnr

    4 plugs give ohm reading but front and back two don’t

    What are you looking for? My tailpipe is black but it doesn't smoke when running so I always just figured it was fine.
  9. UMR_Engnr

    Ign. switch slider bit on a tilt column removal

    Ah, I got it now. Thanks.
  10. UMR_Engnr

    Ign. switch slider bit on a tilt column removal

    Glad you got it sorted. If you don't mind explaining, what did you use the screw and phillips for?
  11. UMR_Engnr

    Ign. switch slider bit on a tilt column removal

    I agree with snicklas the part is called an ignition actuator and you can get it at the local auto parts store for under $15. Not worth pulling a used one that may already be stressed. I replaced mine last winter and separated the two pieces by using a long punch and knocking out the pins from...
  12. UMR_Engnr

    MEP701 Military Generator

    And now for something completely different. https://kansascity.craigslist.org/bar/d/military-diesel-generator-mep/6635534308.html I have for sale a military surplus MEP-701A diesel generator. These are rated for 3kW continuous duty (24/7) by the military, and I've heard they can go up much...
  13. UMR_Engnr

    7.3l idi fuel leak from filter

    You might double check that it isn't leaking from the connector on top of the filter and just dribbling down the sides. This is the fuel heater and is a known leak point. If it is really coming from between the filter and filter head, when you replace the filter check the filter head sealing...
  14. UMR_Engnr

    Making the slug comfortable

    FYI, mid 90s f150 regular cab with buckets has a flat metal subframe that bolts to the bench seat floor points. I think I got mine out of a 94.
  15. UMR_Engnr

    4wd DNE2 Project

    Thanks for the extra info. I may end up copying your idea for my build instead of trying to set it up as a divorced unit.
  16. UMR_Engnr

    4wd DNE2 Project

    Bummer to read about the bad luck with your setup. The idea is intriguing and maybe with the extra crossmember all would be well. When you remove the tailhousing on the tcase you lose the flange oil seal. Did you build a seal into your adapter? Did you seal the adapter to the cases? Did the...
  17. UMR_Engnr

    What kind of gear oil are you guys running

    I used Valvoline SynPower 75w140. It doesn't require a friction modifier additive for limited slip axles.
  18. UMR_Engnr

    US Gear Dual Range / Doug Nash Info

    The motors with the external two pin connector (not with the bolts going through the side plate) seem to not be grounded through the case. I had to put 12V on one pin and ground on the other for the motor to do anything.
  19. UMR_Engnr

    Zombie Slayer: DNE2 Overdrive Install

    The seller and I came to an agreement on price, so I'm going to keep it for parts or to sell later. Looks like I'm back to option #1
  20. UMR_Engnr

    Zombie Slayer: DNE2 Overdrive Install

    Turns out the box I just got was an underdrive even though I explicitly told the person how to turn the shafts and identify them. Any idea on how much the underdrive boxes are typically worth? The box itself looks to be in good condition. Trying figure out what to do.
  21. UMR_Engnr

    Zombie Slayer: DNE2 Overdrive Install

    When you say jams up, do you mean it is hard to shift or somehow the driveline binds?
  22. UMR_Engnr

    Zombie Slayer: DNE2 Overdrive Install

    Do you have a doubler or just the 205?
  23. UMR_Engnr

    Zombie Slayer: DNE2 Overdrive Install

    I've already got all the parts for any of the options. I got the US gear for c6 4x4 pretty cheap on Friday. Figured they don't come up that often and I could always use it for parts. Although it could also show up and be completely trashed. I've honestly not heard many complaints about the...
  24. UMR_Engnr

    Zombie Slayer: DNE2 Overdrive Install

    I just picked up another US Gear dual range box for a c6 with 4x4. So now I have a few options for this project. Here's the breakdown. Option #1: C6 --> BW1356 (flanged) --> new stub shaft --> US Gear --> new rear driveshaft The US Gear would replace the carrier bearing in this setup...
  25. UMR_Engnr

    2018 Oilburners Rally

    I'm still debating the 15 hour drive, but either way I'm looking forward to seeing what agenda you guys come up with.

Latest posts

Forum statistics

Threads
91,310
Posts
1,130,145
Members
24,120
Latest member
SixFourShanks08

Members online

Total: 620 (members: 7, guests: 613)

Share this page

Top