shawn deere's Recent Activity

  1. shawn deere liked pelky350's post in the thread 7.3 idi sounds like powerstroke.

    If the return lines are leaking could be causing air to get into your fuel and that can cause many issues probably make it hard to time...

    Feb 26, 2017 at 10:17 PM
  2. shawn deere liked mu2bdriver's post in the thread Bull Moose vs. R&D pumps.

    This year it will be time for me to replace my pump and I'll be going with a Moose variant. I'm not looking for performance, just a...

    Feb 26, 2017 at 10:06 PM
  3. shawn deere replied to the thread Ats 093 rubber parts.

    Ummm. Ordered last night, is there a surprise for me when it arrives? Lol

    Feb 26, 2017 at 9:50 PM
  4. shawn deere replied to the thread Intercooler w/ wide radiator.

    Hey there. Can you do me a solid? Ive heard some one some where at some point say that an intercooler would increase the turbo lag. But...

    Feb 26, 2017 at 9:45 PM
  5. shawn deere liked rhkcommander's post in the thread Intercooler w/ wide radiator.

    I am planning on doing an a2w setup, with a reservoir for cooling it down further. As I see it: A2w pros: Easier routing two small...

    Feb 26, 2017 at 9:40 PM
  6. shawn deere liked jaluhn83's post in the thread Intercooler w/ wide radiator.

    Use a air to water setup. More bits, but easier to route. I would want an intercooler for anything over about 10 psi. Just because...

    Feb 26, 2017 at 9:36 PM
  7. shawn deere replied to the thread Intercooler w/ wide radiator.

    :popcorn

    Feb 26, 2017 at 9:33 PM
  8. shawn deere liked pelky350's post in the thread Intercooler w/ wide radiator.

    Got the cooler, the piping kit in mail and got intake hat from typ4 before he left for vacation, just a couple of boots and brackets...

    Feb 26, 2017 at 9:32 PM
  9. shawn deere liked pelky350's post in the thread Intercooler w/ wide radiator.

    Ordered cx racing 31x12x3 cooler and 2.5 piping kit and a couple adaptor boots, typ4 gets back to me tomorrow on eta of intake hat and...

    Feb 26, 2017 at 9:31 PM
  10. shawn deere replied to the thread Ats 093 rubber parts.

    Just bought a cdr valve n rubber stuff from ebay for like $85 bones

    Feb 26, 2017 at 9:29 PM
  11. shawn deere replied to the thread 7.3 idi sounds like powerstroke.

    Miight be too advanced now. Lol. If your doing it by ear you want it to quit 'hammering' when it warms up. It can hammer with the cold...

    Feb 26, 2017 at 9:27 PM
  12. shawn deere replied to the thread High idle question.

    Dont move the pump while its running! Also white/blue smoke point tward retarded timing

    Feb 26, 2017 at 2:18 PM
  13. shawn deere replied to the thread High idle question.

    Sounds like you need to advance the timing. Disconnecting the timing advance should make it sound different Loosen 3 nuts and rotate...

    Feb 26, 2017 at 1:32 PM
  14. shawn deere liked Macrobb's post in the thread Rob's '93 at the dyno!.

    Maby, or maby not. I suspect it's cylinder pressures not boost pressure that actually matters. Which means if you are running lean at 20...

    Feb 26, 2017 at 12:00 PM
  15. shawn deere replied to the thread Rob's '93 at the dyno!.

    Thanks for the info! Head studs will have to wait......... i can hook up the waste gate if i need to. Im gonna run out of ambition...

    Feb 26, 2017 at 11:57 AM