Recent content by 88beast

  1. 88beast

    help i found my leak

    ok sounds good if she blows up your coming over to kill the rest f the beer right?
  2. 88beast

    help i found my leak

    you can see the gap in 2 of them. also the exhaust manifold does not have any soot on it. i cleaned the manifold and the area around it before, then put a new gasket on. you can see that there is no soot on the gasket or within 1/4 inch of the manifold. so now to the plan, if doing head...
  3. 88beast

    help i found my leak

    it is the head gasket, i was on the same logic as everyone else, though it does not show any symptoms of a head gasket. i have pics on the phone but need to get them over to the comp, well see if they go through and if so i will post them. between the head and block, right by the thermostat...
  4. 88beast

    help i found my leak

    well been busy and away from the site lately but now its back to finishing the truck. i found my leak, i think. right behind the vacumme pump between the head and block you can feel a rush of luke warm air. i was thinking head gasket but have a few questions before buying a compression...
  5. 88beast

    find the knock help needed

    ya im stumped on that one, but ill figure it out sometime ust got to move the ttruck friday as im moving
  6. 88beast

    find the knock help needed

    ya my buddy says he feels it, but i cannot. the chances of a hg blowing the firering out and not going to a coolant or oil passage is low. also the truck has ran like this for a while, to md and back plus more trips.
  7. 88beast

    find the knock help needed

    heres a vid you can also hear an exhaust leak in this vid ignore that its solved now
  8. 88beast

    find the knock help needed

    got ya never though of the the copper washer did not come out. im assuming its pretty bad shape, im gonna dig it out tomorrow.
  9. 88beast

    find the knock help needed

    i have a knock/ leak. the front pass side of the engine you can hear a knock ( my buddy says its a air leak). yesterday when i cracked the front pass injector the engine did not change, tonite i put a new injector in and now the noise goes away a good bit. as for the part im confused about...
  10. 88beast

    IP Advice

    then idle 5 minutes or so on clean diesel before you turn off, if the pump is shot pm me i got a spare id let go cheap
  11. 88beast

    window motor repair how to

    well i tackled this early this am. and i decided to explain it for anyone who didnt know how. what you will need. drill and drill bit (to drill access holes) phillips #3 phillips #2 basic sockets and ratchets. flat head screwdriver door panel clip removal tool. first remove the...
  12. 88beast

    flatbed

    any aftermarket bed is typically "universal" measure the frame width if its the same it will fit. also see if the bed has flat rails. usually they are made to fit the frame with wood, or another filler. you would just need to make a new filler peice to work for your truck
  13. 88beast

    wanted dipstick

    riot whats shipping to 17109? ya think ya can fit one in a flat rate usps box? or the tube?
  14. 88beast

    truck build update

    well the website is further along. http://ihiditech.comeze.com/Home/ the old ford is now building good boost. i hit about 10 psi today with the tire (open rear) roasting. i have to admit it will climb a hill and has some power. after i regear soon it will be even better. the painless...
  15. 88beast

    wanted dipstick

    im not sure, its stock truck stick, ill gladly cover shipping.
See more

Latest posts

Forum statistics

Threads
91,284
Posts
1,129,802
Members
24,101
Latest member
dieselmainiac

Members online

Total: 760 (members: 7, guests: 753)

Share this page

Top