Forums
New posts
Search forums
What's new
New posts
New resources
Latest activity
Resources
Latest reviews
Search resources
Members
Registered members
Current visitors
Log in
Register
What's new
Search
Search
Search titles only
By:
Registered members
Current visitors
Menu
Log in
Register
Install the app
Install
Members
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
BlindAmbition's latest activity
BlindAmbition
replied to the thread
Shocks for 1991 F350 DRW Rear Wheel Drive Stock Height - Bilstein 5100?
.
I had the same issue when looking for 5100s for my truck. When I called they offered to look up shocks based on specs if I measured...
Mar 20, 2024
BlindAmbition
replied to the thread
buying fittings for the IP from the hardware store?
.
Looked at a few return fittings I have, looks like 1/8 npt to me. Can send one out if you need, send me a message.
Mar 15, 2024
BlindAmbition
replied to the thread
'86 Extended cab project thread
.
Shouldn't be much at all, if any really. The run is super short, something like an 1/8 of the distance for most air to air intercoolers...
Mar 14, 2024
BlindAmbition
replied to the thread
'86 Extended cab project thread
.
Got the intercooler reservoir mounted. Will work on the pump and routing hoses next. 3.4 gallons is overkill but I don't think I'll...
Mar 14, 2024
BlindAmbition
replied to the thread
buying fittings for the IP from the hardware store?
.
Inlet is an ORB/O ring boss, cannot remember the size, maybe 5/16 or 3/8. Return is a standard 1/4 npt I believe.
Mar 14, 2024
BlindAmbition
replied to the thread
'86 Extended cab project thread
.
Finished the oil bypass setup, got the coolant/windshield reservoir mounted, mounted the fuel regulator setup, clocked the turbo and...
Mar 13, 2024
BlindAmbition
replied to the thread
6.9 to 7.3 glow plug harness
.
I'd get some new connectors and create my own harness connections. Something like a WeatherPak or Delphi or Deutsch connector. Just...
Mar 12, 2024
BlindAmbition
replied to the thread
parallel turbos
.
Found the thread. I imagine you could compensate for higher fuel pressure by advancing or retarding the IP timing as needed. Just be...
Mar 9, 2024
BlindAmbition
replied to the thread
parallel turbos
.
10 psi is too high and changes the timing of the pump I believe. My R&D pump came calibrated for 7psi. There is a rather large and...
Mar 9, 2024
BlindAmbition
replied to the thread
parallel turbos
.
Might need to run a vent tube to each intake tube, you're only scavenging from half your cylinders otherwise. Most things I read say to...
Mar 9, 2024
BlindAmbition
replied to the thread
parallel turbos
.
I'd move your crankcase vent to one or both of your intake tubes instead of the end of the air filter. There should be more suction...
Mar 8, 2024
BlindAmbition
replied to the thread
'86 Extended cab project thread
.
Oil line is plumbed. 1/8 npt on the block to 4an fitting and then a 24" line. Oil block on turbo has two feeds, second feed is 4an as...
Mar 8, 2024
BlindAmbition
replied to the thread
Help on timing with a snap on mt1480
.
This thread has info that should help steer you in the right direction...
Mar 7, 2024
BlindAmbition
replied to the thread
'86 Extended cab project thread
.
Mounted a smaller reservoir to be the fill spot for the system. Will likely need to lift it when filling to get the air bubbles out...
Mar 7, 2024
BlindAmbition
replied to the thread
'86 Extended cab project thread
.
Worked on the intercooler reservoir today. It's an old 3.4 gallon propane tank from a VW Westfalia van, was going to use it for my air...
Mar 7, 2024
Latest posts
3G alternator upgrade
Latest: Cubey
Today at 1:15 AM
6.9L IH & 7.3L IDI Diesels
So what did you do with your truck today?
Latest: Nero
Today at 12:12 AM
6.9L IH & 7.3L IDI Diesels
Oil feed line adapter
Latest: The_Josh_Bear
Yesterday at 11:39 PM
6.9L IH & 7.3L IDI Diesels
Afe air filter good/bad?
Latest: Brian VT
Yesterday at 8:33 PM
6.9L IH & 7.3L IDI Diesels
Leaking valve covers
Latest: Nero
Yesterday at 6:02 PM
6.9L IH & 7.3L IDI Diesels
Forum statistics
Threads
91,345
Posts
1,130,760
Members
24,143
Latest member
Cv axle
Members online
No members online now.
Share this page
Facebook
X (Twitter)
Reddit
Pinterest
Tumblr
WhatsApp
Email
Share
Link
Members
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.
Accept
Learn more…
Top