Search results

  1. O

    So what did you do with your truck today?

    I guess that hitch extension is ok, just never thought they were all that safe. Looks like it should have a wheel under it for support.:bail Goat
  2. O

    So what did you do with your truck today?

    Shame you need to see your truck, Probably needs new IP with it hard to start hot etc... just read through your first page of your project thread. You put some work into it. Hate to see anyone sell their IDI truck, then later egret selling it....dang, should have never sold it. Goat
  3. O

    Black sludge/deposits under valve cover - problem?

    I talked to them before. I seem to have $800 in my head, but probably much more. I will have it checked over before sticking it in. There is a deeper sump available, here is a thread. https://www.ford-trucks.com/forums/1259386-gearvender-deep-sump-installation-tutorial-maximum-overdrive.html...
  4. O

    Different Oil Filter (read)

    I use the MotorCraft FL1995 Power Stroke Filter. Walmart has them on the shelf. Use to be $9.97 now up to $26 ea as I remember. When the Covid BS started, and the supply chain shortages, I started buying them when I saw them back on the shelves. Iam well stocked. Goat
  5. O

    Showerhead filter alternative?

    The link I posted and the E-Bay Senders are probably all made in the same Chicom assembly line. If you are going to keep your IDI for the long term, be a good idea to purchase a couple back ups while available. Remember, these are OHM specific for what ever year or generation etc... When I...
  6. O

    New but not

    Welcome to the Forum. Looks like they go up to the 6.0 engine. Scroll the page up to where you see "Staff on line". That will be one of the administrators. Click on his name and start a conversation, and he will direct you. Goat
  7. O

    Showerhead filter alternative?

    Did you check here? https://www.gastankdepot.com/ford-truck-diesel-fuel-sending-units.html Goat
  8. O

    So what did you do with your truck today?

    Dang, looks like the dust storms of the 30`s. Goat
  9. O

    So what did you do with your truck today?

    Those type of wheels are dangerous, plus a P-I-T-A. Bought a home made car trailer with Mobile Home axles under it back around 2012 for $1800. Found it on CL, what a piece of stuff. needed new tires, as they were worse than I thought when we looked at it. They are the odd ball size 14.5 x 8...
  10. O

    86 F-250 E-Bay, What they looked like when new

    Poking around on E-Bay came across this 86 F-250, over priced as usual. Thinking, dang, this is what my truck looked like 38 years ago. Hard to believe no dents in the Bed. Had to laugh when it says "has the over drive trigger". Probably a Gear Vendor. Don`t recognize the turbo set up. Maybe a...
  11. O

    Black sludge/deposits under valve cover - problem?

    Thanks for the reply. I pulled a GV from PNP couple years ago out of a 89, 7.3, C6 trans. Grabbed the GV, $160, then back next day with more tools, for the adaptor, $34. Now looking for the T-19 adaptor. This is the first one I have come across all the years going to PNP. A 2 spd rear end switch...
  12. O

    Black sludge/deposits under valve cover - problem?

    Ford420 I see you have a Gear vendor, how do you like it? Goat
  13. O

    6.9 fuel economy after turbo add and fuel screw increase

    That slipamatic C6 is your problem. Even a T-19 4-spd you will do better. Last Saturday drove from here in Nevada, 4 - 5K ft range over to Santa Cruz, Ca. going over the Sierra 8K ft and down to seal level and back, Over 500 miles. got 18.8 mpg. 2 tanks before that putzin around here was in the...
  14. O

    V-belt tension

    That`s a HF Tire Iron. Use it or some type pry bar between Alternator and the engine to pull the Alt. over to tighten the belt. I did that before discovering the Square Block on the Alt. Just make the belts snug. tbowker info above has the info you need. Goat
  15. O

    Black sludge/deposits under valve cover - problem?

    Running cold, taking it on short drives and not getting up to temp. Only driving 2 -3K miles a year and sitting most of the time, could be some of the issues. A few years ago both Valve Covers were a leaky mess. I cleaned up the Drivers side, removed the bolts and washers, cleaned them up in...
  16. O

    V-belt tension

    I don`t know what the tension is suppose to be. For the Alternator belt, at the top of the Alternator where the bolt screws into is a square block. Put a large open end of correct size or a large Crecent wrench to pull the Alternator over. Then tighten the bolt. using that I never have any blet...
  17. O

    is it possible to change only these rubbers?

    Well that sucks. Reread through this thread again, and searched for Tie Rod/Ball Joints Boots. And now see you need to replace the whole shebang. I hate the Government. :puke...
  18. O

    EGT questions

    You never see older vehicles on the road. When I was a kid, (Graduated in 62) use to always see older vehicles. Always wanted a 50 Ford, back then, but my Dad didn`t want any junk sitting in front of the house. Guess that`s why I have 15 or so parked all around here. Today, I couldn`t tell you...
  19. O

    So what did you do with your truck today?

    I just rolled over 350K yesterday, you better get to crackin the Whip on them Horses. Goat.
  20. O

    "Tank" my 91 Crew Cab Dually

    You will loose the Roll Over Valve with this mod. There is a BB/Marble that closes off the vent tube in a roll over. The Diff vent and even the plastic vent piece in the end of the small hose off the Roll Over Valve will not keep fuel from leaking out of the hose in a roll over event. Just keep...
  21. O

    Freeze plug tool

    In all my searching I have never come across the tool for sale on Google search or E-bay Too# 303-Do45 Plugs E3TZ-6026A Member gandalf has the drawings he will send if you PM him. Probably pricy to have a Machinist make one. knuckle dragger if still around had one he would rent. Goat
  22. O

    Tach sensor

    Is there an "O" Ring/Gasket under the sensor? Don`t have one, but do have the plug. When the Rod`s are knockin, time to shift. :rotflmao Goat
  23. O

    4 speed to ZF5 swap

    That`s a new one. Never heard of auto and manual Starters. Only one starter that goes both ways. :sly I use Power Master 9050. Goat
  24. O

    EGT questions

    5th being OD, the incline will make the Engine work harder even if it is still pulling good and maintaining speed. As you said, drop her down a gear. Intercooler give you a more dense air and may cause it to burn hotter. Just some thoughts. I have read 3" pipe makes it flow better, anything...
  25. O

    Return line question

    I changed mine to rubber hose several years ago. It`s 3/8" hose. As I remember I used a brass fitting, Barb/threaded. Just don`t remember the thread size. When you get the hose on, remember to fill the hose with Fuel, ATF etc... before attaching it to the Filter. Don`t need to add air to the...

Latest posts

Forum statistics

Threads
91,376
Posts
1,131,367
Members
24,177
Latest member
RangerDanger

Members online

Total: 892 (members: 7, guests: 885)

Share this page

Top